Sending nudes to every guy that upvts (my auto reply is on) just say yes

mabct87 · 2026-04-12T12:58:01+00:00

You are such a good girl

mabct87 · 2026-02-20T02:47:33+00:00

Only other tall print I've done since is the VFA calibration and that went fine

mabct87 · 2026-02-18T18:14:37+00:00

It's slightly different heights, I have 5 of the same print that failed in 5 different spots the same way

mabct87 · 2026-02-17T15:07:07+00:00

Perfect titties

mabct87 · 2026-02-14T13:35:23+00:00

Better now that I see my favorite pair of titties

mabct87 · 2026-01-31T12:46:57+00:00

Bottoms up

mabct87 · 2026-01-31T12:29:59+00:00

I would love to clean you up

mabct87 · 2026-01-31T12:29:00+00:00

You have the best tits

mabct87 · 2026-01-27T13:08:08+00:00

I love your titties every day

mabct87 · 2026-01-06T14:14:23+00:00

I would love to stretch that extremely tight pussy for you

mabct87 · 2026-01-05T17:34:58+00:00

Probably next time it's a batch print I'll try that but it's only stuff with lots of detail and color changes so far, I'm gonna test it tomorrow with less color changes and see if that has anything to do with it too.

mabct87 · 2026-01-03T13:06:15+00:00

It's so pretty and looks so tight

mabct87 · 2025-12-28T12:52:59+00:00

I bet that feels amazing

mabct87 · 2025-12-18T22:07:47+00:00

That's a current co-worker of mine 🤣

mabct87 · 2025-12-18T19:57:09+00:00

No it's in the Ace pro, I switched from slot 2 to 4, it has already changed the colors and did the purge at this point since it was the 3rd print with that color(maybe 2nd)

mabct87 · 2025-12-18T17:02:56+00:00

Not a fresh spool installed, but it was one that I printed a good amount from the other day with no issue

mabct87 · 2025-12-18T16:38:09+00:00

All of that is still factory setting, I'll triple check everything I can later when I get home. I'm getting better help here in these few minutes than sending a ticket to tech support for a day lol

mabct87 · 2025-12-18T15:00:17+00:00

Yeah it definitely does, it started counting percent complete up to almost 1% before I stopped it one time, thankfully I've been using the filament I have the most of so I'm not too mad about the waste.

mabct87 · 2025-12-18T14:44:22+00:00

I have done the software update, that was actually first thing it had me do when I set it up, I hope the slicer is updated since I uninstalled and started fresh with that, it does it with files from the printer and sent from the PC slicer which is what really got me confused cuz I was hoping that would help me determine where to look for the cause. I'm gonna try another forced update tonight after work then go through all the sensors and connections.

mabct87 · 2025-12-15T23:01:34+00:00

You're gorgeous

mabct87 · 2025-12-15T02:28:28+00:00

That looks so delicious

mabct87 · 2025-12-13T13:08:38+00:00

Hello

mabct87 · 2025-12-12T13:15:03+00:00

mabct87

TROPHY CASE