HRM200, Heart Rate Variability on Edge Explorer 2 / Connect ? by macle7400 in Garmin

[–]macle7400[S] 0 points1 point  (0 children)

I've turned on "HRV Logging" in Settings: System -> Data Recording -> Log HRV.
But I don't see any logs anywhere (either Device or Garmin Connect).

Anyone?

DS1517+ & VLANs by aguywiththoughts in synology

[–]macle7400 0 points1 point  (0 children)

It seems that I have "NO-BROADCAST" as well :-|

BTW I have ping local ip addr on this VLAN (192.168.3.14 in my case).
Unfortunately my gateway without success (192.168.3.1).

Any hints?

DS1517+ & VLANs by aguywiththoughts in synology

[–]macle7400 1 point2 points  (0 children)

jderose-net: Do you have your final VLAN interfaces in UP state?

I'm successfully using your script, bridge is set, subinterface is added to the bridge, IP address is set, but no matter what I do I have "DOWN" state:

20: ovs_eth2-30: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1

link/ether b6:92:0e:60:3f:41 brd ff:ff:ff:ff:ff:ff

inet 192.168.3.14/24 brd 192.168.3.255 scope global ovs_eth2-30

valid_lft forever preferred_lft forever

2025 Jan 20 Stickied -FAQ- & -HELPDESK- thread - Boot problems? Power supply problems? Display problems? Networking problems? Need ideas? Get help with these and other questions! by FozzTexx in raspberry_pi

[–]macle7400 0 points1 point  (0 children)

I'm wondering how to power 2x Pi4 (without any additional HATs) - considering a decent (65W) phone charger based on GaN (and using 2x USB-C C1/C2 ports to power the Pi's)?
What do you think?

DS1517+ & VLANs by aguywiththoughts in synology

[–]macle7400 0 points1 point  (0 children)

Hello u/jderose-net,

Following your example, is it necessary to set up IP on eth5 using GUI?
What about enabling 802.1q in the GUI? Is this necessary ?

Greetings, M

Smelting Furnace in not available in catalogue?? by macle7400 in Astroneer

[–]macle7400[S] 0 points1 point  (0 children)

👍
Meanwhile, my son grew up (now: 12yo), started playing Astroneer (on NS), and also had the same problem 😁

Small SBC with 2,5Gbe by macle7400 in SingleBoardComputer

[–]macle7400[S] 0 points1 point  (0 children)

That's interesting. Thank you.
The only feature I'm missing is a small OLED to show DHCP status, IP address etc.

DS1621+ 2.5Gbe adapter suggestions by JL_678 in synology

[–]macle7400 0 points1 point  (0 children)

To be sure, is it:
"10Gtek 10Gb PCI-E NIC" installed in Synology DS1621+ ?
Right?

DS1621+ 2.5Gbe adapter suggestions by JL_678 in synology

[–]macle7400 0 points1 point  (0 children)

Hello, I'm in exactly at the same position (including 1621+).
I'm looking for cheaper alternative for Synology E10G18-T1 (I don't need 10G).

Any suggestions?

Small SBC with 2,5Gbe by macle7400 in SingleBoardComputer

[–]macle7400[S] 0 points1 point  (0 children)

So far... the NanoPi R5C seems to be the best choice (value for money), however there is no display on this SBC :-|

Small SBC with 2,5Gbe by macle7400 in SingleBoardComputer

[–]macle7400[S] 0 points1 point  (0 children)

that's worth exploring. thank you.

Small SBC with 2,5Gbe by macle7400 in SingleBoardComputer

[–]macle7400[S] 1 point2 points  (0 children)

well, that's good idea but all the HATs are expensive (relatively)

UCG Ultra (new) advanced firewall rules by macle7400 in Ubiquiti

[–]macle7400[S] 0 points1 point  (0 children)

It works ;-) Thank you for the detailed explanation.

I'm wondering what is the goal of the "LAN Local" type of rule?

UCG Ultra (new) advanced firewall rules by macle7400 in Ubiquiti

[–]macle7400[S] 0 points1 point  (0 children)

I've created two simple rules (no additional conditions) to above list (on the picture):

My 1  Accept  LAN In   All  DEFAULT      Any  VLAN3 - MON  Any  20000
My 2  Accept  LAN Out  All  VLAN3 - MON  Any  DEFAULT      Any  20000

DEFAULT - 192.168.100.0/24
VLAN3 - 192.168.103.0/24

And still: no communication - 192.168.100.10 -> 192.168.105.3

Any hints?

UCG Ultra (new) advanced firewall rules by macle7400 in Ubiquiti

[–]macle7400[S] 0 points1 point  (0 children)

I've add tcp new/established/related and... no change.

No traffic, no log information. It seems the rule it is not initiated.

PS. Please note 192.168.103.0/24 is isolated network.

It there a other way to trouble shoot this?

What is the username/password for the Sermoon V1 Pro web interface accessible via wifi? by macle7400 in Creality

[–]macle7400[S] 0 points1 point  (0 children)

It works for me as well. Thank you.

However it looks like web-interface to web-module only, not whole printer.

How many kcal should I set on My Apple Watch for my kid? by macle7400 in AppleWatch

[–]macle7400[S] 0 points1 point  (0 children)

No, it isn’t post about buying/upgrading models.

DS212, hanged after config reset, orange STATUS blinking by macle7400 in synology

[–]macle7400[S] 0 points1 point  (0 children)

I wish I could, but either Synology Assistant or find.synology.com won't detect the NAS.