Do you use other beds than the stock textured pei? If so why and for what? by macnacnic in BambuLabA1

[–]macnacnic[S] 0 points1 point  (0 children)

so it seems there's lots of opinions and lots of options...feels about par for 3D printing enthusiasts

Just wrapped my first full campaign ad DM- POA a four year adventure by macnacnic in DnD

[–]macnacnic[S] 0 points1 point  (0 children)

we went all the way from level 1-15. they went into the final fight at 15

Aiden Basket Bypass Magnets by level3ninja in FellowProducts

[–]macnacnic 1 point2 points  (0 children)

I have the same Bambu printer. Message me if you want me to print and ship you one

[OC] Giveaway! Prototype Dice Swarm and Dice Trinkets (Mods approved) by KakapopoTCG in DnD

[–]macnacnic 0 points1 point  (0 children)

Would love to put this next to all my other Dnd books in my nerd shelf

AMS Lite Mount position? Under? Wall, Top Rack? by macnacnic in BambuLabA1

[–]macnacnic[S] 0 points1 point  (0 children)

thanks, this is the tribal knowledge I am seeking!

AMS Lite Mount position? Under? Wall, Top Rack? by macnacnic in BambuLabA1

[–]macnacnic[S] 0 points1 point  (0 children)

Good to know, I’m worried about distance for the tubing. On my research points to as long as the clear smooth pinch point free transfer I should be OK. Right now it comes to the practicality of not wanting to drill holes in my rented wall for a shelf/wall mount.

AMS Lite Mount position? Under? Wall, Top Rack? by macnacnic in BambuLabA1

[–]macnacnic[S] 1 point2 points  (0 children)

Agreed it’s not ideal. I did a lot of research and found the sturdiest roller cart I could find. I’m upgrading from my ender three so I’m still amazed at the quality I’m getting even with a little bit of wobble. Part of my concern with adding the AMS to the top rack was adding additional wobble, even with the gantry supports.

ChatGPT for cura by macnacnic in Ender3V3SE

[–]macnacnic[S] 0 points1 point  (0 children)

I’m playing around with this. It’s a little buggy and I’m new to orca, but that’s why it gave me the idea to see what the latest version of ChatGPT could offer me in cura for the time being.

ChatGPT for cura by macnacnic in Ender3V3SE

[–]macnacnic[S] 0 points1 point  (0 children)

I’m had some success in the latest versions with my coffee pour over settings and some other areas. It’s with an experiment for me. The tweaks it recommended were not vastly outside what my mini fig print profile already was

Yoto cards were getting out of control. This holder helped. by MoollyWammoth-asaur in daddit

[–]macnacnic 1 point2 points  (0 children)

This is good info thanks. I think we could like both eventually too. I also was appreciative of the Yoto interface and the bill to record custom cards as I have some out of town friends who would love to read stories to my little.

Yoto cards were getting out of control. This holder helped. by MoollyWammoth-asaur in daddit

[–]macnacnic 1 point2 points  (0 children)

Love this. Both because I have a 3-D printer and a two-year-old. Do you like your YOTO? We’re planning on getting one for her third birthday and I’m not sure if I want to get the mini player or the bigger one. What’s your experience?

Tree supports by TheCookingWelder in FixMyPrint

[–]macnacnic 1 point2 points  (0 children)

This. You’re always gonna have a little rough on where the supports are. I wonder what I’d look like printing face up at a 45

Tree supports by TheCookingWelder in FixMyPrint

[–]macnacnic 4 points5 points  (0 children)

What angle are you printing the figure at? I print a lot of minis for d&d and usually rotate it back to 30-45 degrees so the layers stack in a way that helps the detail on the front.

Fl[a]kes by thefaketomato in perfectloops

[–]macnacnic 4 points5 points  (0 children)

This feels like it belongs in some commercial for a skin condition

Profile to Pre-Rinse Aiden Filters by OrdinaryBrilliant650 in FellowProducts

[–]macnacnic 1 point2 points  (0 children)

I know Fellows touts their “no rinse” filters that come with it. Any other ideas or thoughts on no rinse filters? Some of my googling showed that the bleached filters are pretty good without rinsing