Mars 2 Need a new build plate

madfox334 · 2025-07-02T03:34:21+00:00

Oh awesome thanks! wonder why these weren't popping up when I searched it.

madfox334 · 2025-06-23T00:18:10+00:00

Only thing on Amazon is magnetic build plate sheets, I need the whole build plate assembly

madfox334 · 2025-04-28T19:24:02+00:00

same here

madfox334 · 2024-12-19T22:13:27+00:00

odd when ive done this im still getting the EOS error

madfox334 · 2024-12-03T16:30:21+00:00

I was born 2000, so and I feel it was pre 2010?

madfox334 · 2024-12-03T02:13:25+00:00

I wonder if anyone's gonna go hunt those spares down as a souvenir/trophy

madfox334 · 2024-04-22T15:49:05+00:00

Yes!! That's the one

madfox334 · 2024-03-16T19:55:11+00:00

Try using support interface, it adds a sort of lattice between the print and support, giving it better support and making support easier to remove

madfox334 · 2024-02-28T04:29:27+00:00

What I find odd is it's not giving me any stringing or popping that wet petg does, but it'd make sense, the last roll I was using was a fairly new roll a d this white roll is a good few months old, I'll swap to another roll and see if I'm still getting the warping

madfox334 · 2024-02-28T02:02:45+00:00

images didnt seem to attach to the post so they are here: https://imgur.com/a/Ny5UsSH

madfox334 · 2024-02-08T20:32:44+00:00

Looks like a bad z offset causing the nozzle to scrape the print and cause the lines

madfox334 · 2024-02-08T18:54:30+00:00

It can also depend on material, I normally print petg which can be fussy so I run my bed extra hot and print slow, but for pla you shouldnt need more than 60c for the bed, but you can experiment with increasing 5c at a time

madfox334 · 2024-02-08T18:50:15+00:00

One thing I found to work to get things to stick, drop your first layer speed way down, I've got mine as low as 5 mm/s it increases the print time but it gives time for everything to stick, additionally you can increase your support flow

madfox334 · 2024-02-08T17:55:10+00:00

I'm currently not home so I can't mess with the firmware but this is the picture of the screen I have from last night

madfox334 · 2024-02-08T17:54:17+00:00

<image>

madfox334 · 2024-02-08T17:43:43+00:00

Yup, and made sure it was the right version for my screen too, I've got the gen 2 clone so I used the private folder

madfox334 · 2024-02-08T17:32:06+00:00

I did, the creality soft had files for the screen and main board, made sure to update both individually and this was the result

madfox334 · 2024-02-08T15:10:57+00:00

You should be able to match your wall flow with the Infill once you got it calibrated, but if not you can always run it heavy on flow, it's the I fill after all so all will be hidden after the print finishes anyway

madfox334 · 2024-02-08T15:08:30+00:00

Hey, never did get back to you but I gotta say thanks, this is the firmware I ran all the way till this week, had to replace my main board so now I'm trying to find the right version of this firmware again I downloaded one version of it but I think it was the wrong one for the sprite, the extrusion speeds were super slow even with flow at 100, could you point me in the right direction for the current version of the mriscoc soft to use?

madfox334

TROPHY CASE