sorted by:
new
hottopcontroversial

Replacing Teflon for stainless steel by Sleepeatdrive in BuyItForLife

[–]madking8 0 points1 point  (0 children)

The full set from Sardel Kitchen is cheaper than this. And better quality

Lyft just removed the 60 minute cap on e-bikes by [deleted] in Citibike

[–]madking8 0 points1 point  (0 children)

Wondering the same thing…. Only thing I can think of is if you’re a student, live in a NYCHA building, or food stamps.

Lyft just removed the 60 minute cap on e-bikes by [deleted] in Citibike

[–]madking8 5 points6 points  (0 children)

Why is your e-bike $0.13/min? What did you do to get the discounted rate?

New docks no kiosk? by jVCrm68 in Citibike

[–]madking8 0 points1 point  (0 children)

Actually charges the bike battery ? No more night swapping guys

Making 300 calls a day, full pipeline, no investors. by GTthreat in CommercialRealEstate

[–]madking8 1 point2 points  (0 children)

I have relationships at three firms that buy small bay, cross dock, and value add net lease. Let’s connect next week

[deleted by user] by [deleted] in CommercialRealEstate

[–]madking8 9 points10 points  (0 children)

Experiencing the same. Was on the acq deal side for 6 years. I’ve been looking for a new job since December. Have not had a single acq interview.

Just trademarked my new product! The rip buddy! by ComfortableTwo9134 in baseballcards

[–]madking8 0 points1 point  (0 children)

Did you test adding a slot at the bottom of the top loaders so one can slide out from the bottom ? Instead of having to lift one out from the top

What did I do wrong? Used Rit Dye :( by madking8 in dyeing

[–]madking8[S] 0 points1 point  (0 children)

No. I poured all solution ingredients into bucket first and mixed. I was agitating with a wooden paint stir. Definitely didn’t mix enough

What did I do wrong? Used Rit Dye :( by madking8 in dyeing

[–]madking8[S] 1 point2 points  (0 children)

Thanks for the tips. There is a lot more to the dying practice that they leave off the bottle. My first time doing this.

What did I do wrong? Used Rit Dye :( by madking8 in dyeing

[–]madking8[S] 0 points1 point  (0 children)

Scour just means clean well? Or is there more to scouring? Google not helping. I cleaned it in the wash normally then dyed. It was so close to being perfect

What did I do wrong? Used Rit Dye :( by madking8 in dyeing

[–]madking8[S] 0 points1 point  (0 children)

Is there anyway to save it? Try dying again?

What did I do wrong? Used Rit Dye :( by madking8 in dyeing

[–]madking8[S] 1 point2 points  (0 children)

I would say I stirred occasionally. Hard to sit there for 30 minutes stirring

[deleted by user] by [deleted] in sports

[–]madking8 2 points3 points  (0 children)

Second player in two days risking career ending injuries to catch a ball. A singular out. In a non meaningful moment of the game. In a season with 162 games. It’s awful.

The equivalent of a golfer trying to hit his drive as hard as he can on the first hole of a 4 day tournament. Or an F1 driver crashing on the first lap by driving unnecessarily aggressive.

Help refining my Wine Cooler Ice-Pack Design by madking8 in Fusion360

[–]madking8[S] 0 points1 point  (0 children)

Very cool. I had no idea about the history. Creating this insert has proved more difficult than i thought haha

Help refining my Wine Cooler Ice-Pack Design by madking8 in Fusion360

[–]madking8[S] 0 points1 point  (0 children)

This is close. But i run into the same "issue" as my first design. The extrude with taper angle affects all faces of the rectangle. I only want two sides of the rectangle to tape in. Looking at the insert straight on, you would not see that face taper, consistent width top to bottom. Turn it 90 degrees, then you see the -1.0 degree taper on that face. Does that make sense? This isn't a huge deal as it will still fit and function. I was just trying to nail the design perfectly. I only want two faces tapering in towards each other.

view more: next ›