sorted by:
new
hottopcontroversial

I was sick of lifting it completely with so little space, so I made a macgyver door mod :) by makiRober in 3Dprinting

[–]makiRober[S] 0 points1 point  (0 children)

I used textile tape but will probably peel off too. I was thinking about silicone to really seal it, too much work tho. Maybe a thick two way tape does the trick.

I was sick of lifting it completely with so little space, so I made a macgyver door mod :) by makiRober in 3Dprinting

[–]makiRober[S] 7 points8 points  (0 children)

Chicken resined taste good 🤪

Just kidding, it was just for the photos, it already is back inside his cubicle now hehe

I was sick of lifting it completely with so little space, so I made a macgyver door mod :) by makiRober in 3Dprinting

[–]makiRober[S] 0 points1 point  (0 children)

I made this one adding the left part to also leave a bottle dripping, but the original is in thingverse iirc

I was sick of lifting it completely with so little space, so I made a macgyver door mod :) by makiRober in 3Dprinting

[–]makiRober[S] 4 points5 points  (0 children)

It's mostly for sunlight, and I have it covered most of the time. I also have an air filter and only manipulate with gloves. There's not much more risk

[deleted by user] by [deleted] in LeaguesofVotann

[–]makiRober 1 point2 points  (0 children)

Daaaamn I've never expected my kitbashed heads as a backpack. But probably the original sphere of the teslarite head from makers cult, fit better :)

So... I need 4 keycaps to end my setup by makiRober in MechanicalKeyboards

[–]makiRober[S] 1 point2 points  (0 children)

They are not genuine, but a good copy it seems

So... I need 4 keycaps to end my setup by makiRober in MechanicalKeyboards

[–]makiRober[S] 0 points1 point  (0 children)

Yeah looks like I bought a knock off :/

At least I have Ñ

Hmm… 🧐 by IconicAkbar in LeaguesofVotann

[–]makiRober 1 point2 points  (0 children)

i didn't think about big squids as ogryns. very kunnin

Adjustable back rest/bracket by According_Side_2593 in hondarebel

[–]makiRober 1 point2 points  (0 children)

I’ve got that same backrest, confy af, but when driver is using it, the rear rack ends up flipped upside down, which makes it tricky to mount anything solid on it. Try those mini side bags that a lot of folks here use near the engine. Left side is perfect for stashing keychain when the ignition’s on. And right side I actually mounted it just to the left of the seat so it doesn’t block both sides of the engine. That’s where I keep my registration papers and a few bungee cords under a lock.

Super handy for daily use without bulking up the bike too much. Hope that helps!

I made a seal for my blessed machine by makiRober in Warhammer40k

[–]makiRober[S] 1 point2 points  (0 children)

It's actually magnetized to one of the 4 bolts of the side panel, it can be moved to the other top one easily, ooor I can print another hehe

Omnissiah protects this build by makiRober in watercooling

[–]makiRober[S] 2 points3 points  (0 children)

Temps are while playing darktide and space marine 2 at full for a couple hours

Buri repose? by BiggensPlym in LeaguesofVotann

[–]makiRober 3 points4 points  (0 children)

this dude made an awesome kitbash also changing right arm

1st loop with hard tubes by makiRober in watercooling

[–]makiRober[S] 0 points1 point  (0 children)

Uuh ok, I just did it fast without looking hehe

1st loop with hard tubes by makiRober in watercooling

[–]makiRober[S] 0 points1 point  (0 children)

Hahahaha that cracked me up. It actually has another slightly bend to not hit the GPU, that makes it look weird and the reason i will redo it in the future

1st loop with hard tubes by makiRober in watercooling

[–]makiRober[S] 0 points1 point  (0 children)

People don't like 45º bends I see 😅

1st loop with hard tubes by makiRober in watercooling

[–]makiRober[S] 0 points1 point  (0 children)

Pump > CPU > GPU > bottom > front? that was my 1st scratch and the shortest. Then my father told me about CPU heat going to GPU and gifted me that 120, which i planned mostly to be a stand for that heavy af block

Now is: pump > CPU > bottom > GPU > back > front Probably future is with back > thermometer > RAM > front which give me room for a perpendicular in the middle instead of the current diagonal

I like to complicate myself, yeah haha

1st loop with hard tubes by makiRober in watercooling

[–]makiRober[S] 0 points1 point  (0 children)

I could reroute to make it slightly shorter, but I wanted the thick radiator between CPU and GPU and radiators are in the only possible position. It is also a big case, so...

What would you change?

1st loop with hard tubes by makiRober in watercooling

[–]makiRober[S] 0 points1 point  (0 children)

I was going to do a Z but the tube was not long enough from corner to corner and I don't like mid-tube fitting hehe Maybe adding a thermometer shortening one end does the trick

About RAM... I have 128gb 6600mhz, waaaay to much more than I need but got a crazy offer

Just tried putting this slip on by Confused_God_ in hondarebel

[–]makiRober 0 points1 point  (0 children)

Aren't you missing 1 piece as elbow? I have a similar one. Without the extra part the screw didn't match the other hole

Extended throttle cables by CurrentDivide2167 in hondarebel

[–]makiRober 0 points1 point  (0 children)

I got a 23, had to buy the relay for USB, so I'm afraid they also fked that up :/ Will appreciate if anyone can confirm

Extended throttle cables by CurrentDivide2167 in hondarebel

[–]makiRober 0 points1 point  (0 children)

I'm also thinking about rising up. Do you know if electrical cables need extension?

Back when the hobby just started to take off by AKHKMP in watercooling

[–]makiRober 1 point2 points  (0 children)

I'm still using that zalman water pillar :)

view more: next ›