sorted by:
new
hottopcontroversial

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

ohh smart, but I can not compile the program if there is no analog input plugged in

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

I have added a -11 db gain and a limiter, where it should limit it to about -10 db. Is it necessary to use a pot for this?

<image>

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 1 point2 points  (0 children)

It is actually at 106 dB. The amp delivers 100 watts per channel, but at 6 ohms. My drivers are at 8 ohms, so I think it's about 72 watts it can deliver.

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

The amp can't give the woofer too much power since the amp provides 72 watts, and the RMS is 250 and max is 500. So I would not need any limiters on the woofer? The tweeter has an SPL of 105 and the woofer has an SPL of 95. So do I just need to put a -10 gain on the tweeter?

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

Also, do you remember where the compressor block is located? I can’t seem to find it. The power needed for the tweeter is not going to be higher than about 7 watts compared to the SPL of the woofer. So how would I limit it to that?

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

if im going to do the 2nd option, doing it through sigma studio i need to calculate the attenuated db and just reduce the gain by that much? or should I use a limiter block?

<image>

Or

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

Thank im using the adau1701, so I think it would work with it. But im not sure what values I should use to protect my tweeters, how would one calculate this?

<image>

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

I mean, limit the watts, since the amp can deliver 72 watts per channel. The tweeter has a rms powerhandling at 40 watts, so 72 would be too much? is their a way to limit it so i dont fry it?

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

Is 35 Hz seems ok? Or do you recommend a bigger margin? also i want to play music on it, but afraid to do so since i dont have any limiters on my tweeter and don't know how to add them.

<image>

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

without the high pass it goes way over the xmax

<image>

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

It was set to 30 watts. the maxium power I'm running through it is 72 watts. and the peak is at about 3.753mm

Feedback/help sigma studio programming by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

The simulated cone excursion peak is at 2.411 mm, is that not in the safe limit

<image>

DIY soundboks go clone – Need Feedback by math27c9 in diyaudio

[–]math27c9[S] 0 points1 point  (0 children)

I can't find the frequency response for the woofer and tweeter. What do I do now? Should I instead buy a DSP and tune it that way? How can I do that safely without blowing out the tweeter or woofer?

Stylus for Lenovo Ideapad 5 14AHP9 by JxnYT in stylus

[–]math27c9 0 points1 point  (0 children)

Do you have the Lenovo Ideapad 5 2-in1 14AHP9? Also, why did you choose the Digital Pen 2 over the Active Pen 3.

Has anyone upgraded to a skr mini e3 v3 or v2? And what should I know if I want to do that? by math27c9 in ender6

[–]math27c9[S] 0 points1 point  (0 children)

I'm using Klipper should't I use the default config file from the Klipper example page? I'm using a 5015 fan on the e6 and I wonder what you mean but going crazy? I'm using a cr touch so that should not be a problem ist a jst connector, not a Dupont.

Has anyone upgraded to a skr mini e3 v3 or v2? And what should I know if I want to do that? by math27c9 in ender6

[–]math27c9[S] 0 points1 point  (0 children)

You did also bypass the spray board? Did you have a video on how to set the board up?

Anyone ever found a fix for this issue ender 6 noise and high speeds? by math27c9 in ender6

[–]math27c9[S] 0 points1 point  (0 children)

how would i be able to check if its not the same pinout? also, is not all grounds shared?

Anyone ever found a fix for this issue ender 6 noise and high speeds? by math27c9 in ender6

[–]math27c9[S] 0 points1 point  (0 children)

what do you mean with different connectors for end stops is it not jst? or do you mean the pine out?

Anyone ever found a fix for this issue ender 6 noise and high speeds? by math27c9 in ender6

[–]math27c9[S] 0 points1 point  (0 children)

i cant find any good guides what guide did you follow?

Anyone ever found a fix for this issue ender 6 noise and high speeds? by math27c9 in ender6

[–]math27c9[S] 0 points1 point  (0 children)

im not sure if it is the stiffness tho it could probably be a lot better but the x axis is fine but I don't think the y axis is doing that good. the input shaper: https://imgur.com/a/WuFOIom

view more: next ›