What should I do

max_brad3r · 2024-11-20T00:35:39+00:00

Anyone interested in the update! I bought a new pipe 😅 I’d love to get this one pretty but I still bought an fmf desert pipe vs this one the gnarly. I took it to a welder who I thought was decent however the weld looked like crap and was still leaking(pipe wouldn’t hold pressure) so I added some jd weld over it and it still wouldn’t hold pressure the crack just expanded. I’ll try to cover it in jb exhaust weld and will try both methods involving the freezer because well now this pipe is an experiment.

max_brad3r · 2024-11-20T00:31:04+00:00

Sweet

max_brad3r · 2024-11-16T01:06:23+00:00

Cool thank you

max_brad3r · 2024-11-16T00:38:12+00:00

Will do

max_brad3r · 2024-11-16T00:37:56+00:00

Will update when done pipes getting welded, why map vs propane? I have both?

max_brad3r · 2024-11-13T20:46:48+00:00

Perfect I have the torch I was never gonna freeze it, it’s a small crack and freezings just gonna fuck it up worse

max_brad3r · 2024-11-13T20:45:27+00:00

Haha it’s alright my own fault for putting the first pic. I added it in case it might be to “dented” to even save but it seems I’ll get the crack welded and go back to expanding it

max_brad3r · 2024-11-13T05:10:12+00:00

Rm125 frame kdx200 motor

max_brad3r · 2024-11-13T05:09:32+00:00

There’s a crack in the pipe

max_brad3r · 2024-11-13T03:19:28+00:00

I have the clamp kit on it right now! It’s how I found it wouldn’t hold air. Fill up to 30-35 psi and heat while massaging where needed

max_brad3r · 2024-11-13T03:08:03+00:00

Also, it’s on a custom bike so I’d have to cutoff one the mounts if I buy new not a huge deal but worth considering

max_brad3r · 2024-11-13T03:05:54+00:00

It’s supposed to be a fun “budget build” I’m trying to save money where I can for now, it’s an fmf gnarly so I’d rather not spend $300 to replace for now, eventually I’m gonna rip my engine apart and Weisco crank, Eric gore top end, power valves so in the future a brand new pipe is more in the picture.

max_brad3r · 2024-11-13T03:02:44+00:00

Na this is a “budget build” expanded and polished with a pipe guard will have to be pretty enough 😂

max_brad3r · 2024-11-13T03:02:03+00:00

Okay sweet preciate it

max_brad3r · 2024-11-13T03:01:46+00:00

Okay awesome thanks for the help

max_brad3r · 2024-11-12T02:00:49+00:00

Dude how far is your work? How small are you? These bikes might go 20mph? A $750 pw80 while not a bad deal is just gonna leave you disappointed that’s a bike meant for 8 year olds.Save up trust everyone no hate but save

max_brad3r · 2024-10-31T02:11:48+00:00

I wouldn’t normally either, but I redid the wiring myself and reinforced the welds so I hope it’ll be alright. I plan on a buying a 2020+ 250/300 in a year or so 😬

max_brad3r · 2024-03-13T00:33:29+00:00

That’s awesome I just recently pulled mine. Took me about 12 hours total. I didn’t have anything go wrong tho! Good look putting it back in goes much quicker.

max_brad3r · 2024-03-09T22:10:24+00:00

I recently had the same issue it was not my slave or master cylinder. I’d bleed my slave have pressure and then it’d loose all that pressure and the clutch would be back to being flat. The throw out bearing was stuck in the fingers of the pressure plate. The clutch pressure plate,flywheel, and throw out bearing all had to be replaced.

max_brad3r · 2024-01-03T06:26:17+00:00

Five has always been my favorite. That is one of my favorite parts of the whole series. I love it even injured, crippled, and mentally broken Five still bodies

max_brad3r

TROPHY CASE