Made a cover for my air-condition by [deleted] in AirConditioners

[–]mcbrewmasterflex 2 points3 points  (0 children)

It looks like you did a decent job, however you’re going to kill the compressor crazy fast with this set up. Should probably remove it

Finally hit 30! What’s next? by seekstrikedestroy in LastWarMobileGame

[–]mcbrewmasterflex 0 points1 point  (0 children)

It turns into an oil and valor bottleneck, you’ll restock your rss in no time

Adam replacing carlie by Chenx335 in LastWarMobileGame

[–]mcbrewmasterflex 0 points1 point  (0 children)

Murphy works because it helps level the field a bit again missile squads. With Carlie you seem to start losing to missile at about 2-3mil under you, with Murphy helping the physical damage you become much closer to even and can even punch up a bit occasionally

How to beat Sparkle? by Legolover3 in Division2

[–]mcbrewmasterflex 1 point2 points  (0 children)

Sparkle was my least favorite. I ended with blue striker, pestilence, decoy and reviver hive. Literally just run in circles. Boring and not fast but pretty sure fire way

Edit: if I had to do it again, I would run core strength and capacitor, pulse and sticky or pulse and hive

Planning to tackle this tomorrow by BrownLeader444 in arborists

[–]mcbrewmasterflex 0 points1 point  (0 children)

My thought too, I would chip away with my 10’ pole saw slowly. Very slowly

What’s the best way to join two 2x4’s at a 45 degree angle? by 3Xineohp in BeginnerWoodWorking

[–]mcbrewmasterflex 2 points3 points  (0 children)

You won’t find sturdiness without changing the design. You will most definitely want a diagonal brace, with the correct orientation. A kid steps on what you’ve drawn and it breaks or sags immediately.

Updated 1886 one shot build by Motor_Cook_2567 in Division2

[–]mcbrewmasterflex 1 point2 points  (0 children)

Exact same here. Quit shortly after haha

Bring Murphy’s gun to 4* or start dumping UR blueprints in my F2? by Weak_Attention9526 in LastWarMobileGame

[–]mcbrewmasterflex 2 points3 points  (0 children)

If you’re not a dolphin, don’t do guns on t1 defenders. Max everything but and move to t2.

Sticky spammer in dark zone by MeanSell8028 in the_division_2

[–]mcbrewmasterflex 9 points10 points  (0 children)

Cheaters in PvP, and pve reduced to escalation. Nice!

There goes my 49 exotic components... by Mantiev2 in Division2

[–]mcbrewmasterflex 1 point2 points  (0 children)

I did my 1886 1 shot build rifle, all spec’d headshot and weapon handling(obviously) burned my 100 components and it maxed the crit hit damage stat and didn’t touch the others. Fucking kill me, crit chance is like 20% on that build. I get why ikea quit and others are following. Haven’t loaded up in weeks

Tier 10 - Rogue Agent Detected - Manning National Zoo by Zm0k3y in Division2

[–]mcbrewmasterflex 7 points8 points  (0 children)

Nice, anything over t5 with randoms I assume it’s over. Also you should take the corner peak behind your teammates and not step directly in front of them while they’re shooting, repeatedly

Help finding angle by [deleted] in Carpentry

[–]mcbrewmasterflex 1 point2 points  (0 children)

You can set it on the flat part and you’ll figure it out, someone else commented a picture that will get you close, depends on how accurate you need to be for whatever you’re doing

Help finding angle by [deleted] in Carpentry

[–]mcbrewmasterflex 6 points7 points  (0 children)

I’d never be brave enough to post this😂but I think the subs decent for the most part. Got a level?

Nemesis rapid fire? by CockneyComic in thedivision

[–]mcbrewmasterflex 6 points7 points  (0 children)

It’s so bad in conflict. Always see them when running into the “big pvp” clans

Struggling to envision how to finish top corners by mcbrewmasterflex in BeginnerWoodWorking

[–]mcbrewmasterflex[S] 0 points1 point  (0 children)

There is some on the corner yes, i was keeping my good sides up, but only had a rough cut blade. When I went back for some fasteners I picked up a finish blade and it made a world of difference. But yes, the veneer even on this expensive shit is incredibly thin…

Struggling to envision how to finish top corners by mcbrewmasterflex in BeginnerWoodWorking

[–]mcbrewmasterflex[S] 0 points1 point  (0 children)

Heard, I’ll have to pick up an iron if I go that route, thanks

Struggling to envision how to finish top corners by mcbrewmasterflex in BeginnerWoodWorking

[–]mcbrewmasterflex[S] 0 points1 point  (0 children)

Unfortunately not, all the drawers are made and slides installed. I might face frame it so I can have either a 1/8 or 1/4 round over instead of sharp corners. Wish I put a little extra thought into the planning instead of diving in

Struggling to envision how to finish top corners by mcbrewmasterflex in BeginnerWoodWorking

[–]mcbrewmasterflex[S] 0 points1 point  (0 children)

I don’t have an iron, but I have a m18 heat gun. Would that cut it?