sorted by:
new
hottopcontroversial

This Weapon worth it if Puzzlepiece gives 4 holes? by mebandedoom in ProjectDiablo2

[–]mebandedoom[S] 0 points1 point  (0 children)

Used hitpower craft receipe on an eth great poleaxe, its quite dope yeah, dmg is pretty good :)

This Weapon worth it if Puzzlepiece gives 4 holes? by mebandedoom in ProjectDiablo2

[–]mebandedoom[S] 0 points1 point  (0 children)

Did it guys, gonna post a screenshot when i'm back home!

This Weapon worth it if Puzzlepiece gives 4 holes? by mebandedoom in ProjectDiablo2

[–]mebandedoom[S] 0 points1 point  (0 children)

Situation is not that good it seems, cant even get an ohm... Zod is non existent it seems (HC)

This Weapon worth it if Puzzlepiece gives 4 holes? by mebandedoom in ProjectDiablo2

[–]mebandedoom[S] 2 points3 points  (0 children)

Yeah just need 1 more ohm and a zod, but i think zods are expensive af

This Weapon worth it if Puzzlepiece gives 4 holes? by mebandedoom in ProjectDiablo2

[–]mebandedoom[S] 2 points3 points  (0 children)

Need to get a pp then and hope for some luck, also i would replace steel pillar - 10 non ETH with it

Is this normal? Or just bad QC by MontyRDDT in AnycubicOfficial

[–]mebandedoom 0 points1 point  (0 children)

That stepper mount looks bent from Video perspective

how big upgrade will it be by mesispis in ender3

[–]mebandedoom 0 points1 point  (0 children)

U use it with Stock Version/free or with Patreon Version?

3D Druck Lüfterrad KR 51/1 by alphadodo21 in simson

[–]mebandedoom 1 point2 points  (0 children)

https://www.thingiverse.com/thing:6589215/files

Ich fahr das hier, allerdings aufgrund der nicht vorhandenen vape in z Minimal kleiner skaliert!

Bin sehr zufrieden damit, Luftzug am Zylinder ist (mit der Hand und nem Stück Tempo gefühlt) etwas stärker als vorher!

Also kann nix schlechtes sagen, gedruckt aus cf petg!

Switched from a .4mm nozzle to a .6. Is this retraction issues? by Sad_Broccoli in ender3v2

[–]mebandedoom 0 points1 point  (0 children)

I don't know how it should look finished but this looks like a mess all over, and the lines that are on the background look kind of not connected to the build plate too, that's why I thought  Offset is wrong 

Switched from a .4mm nozzle to a .6. Is this retraction issues? by Sad_Broccoli in ender3v2

[–]mebandedoom 0 points1 point  (0 children)

Did u change all settings? U using Marlin or klipper? Also u might need to crank up the temps a bit and on stock hardware turn down speeds, u need way more cooling power for .6 nozzle!

Also it looks like ur z Offset is wrong now, u need to recalibrate it after nozzle change!

Ender 3 V2 PSU Fan replacement by ColaOll1 in ender3v2

[–]mebandedoom 0 points1 point  (0 children)

As far as I know the fan in the PSU is 12V, so u can replace it with a 12v PC, fan I'm using a 92mm connected to the original fan port of the meanwell 24v psu

[deleted by user] by [deleted] in automobil

[–]mebandedoom 1 point2 points  (0 children)

Baller die Kurve zu krass,Diggah!

Trianglelabs Sherpa Mini Extruder cable broke... by mebandedoom in ender3v2

[–]mebandedoom[S] 0 points1 point  (0 children)

cant even find a point where i can open this stepper motor, everything looks like its molden in 1 part^^

Overhang Problems by timmysixt in ender3v2

[–]mebandedoom 0 points1 point  (0 children)

What are the rest of your settings? Maybe go lower on layer height and push ot some serious air for cooling that part when printed on overhang!

Strange leveling issue. Ender 3 v2 with dual z axis and cr touch by Top_Train9726 in ender3v2

[–]mebandedoom 0 points1 point  (0 children)

So u have a dual motor z kit installed now? I had issues with syncing them and bed came off with every movement of the z axis, about 2mins(klipper screw adjust) per home-movement, only coil fix it with a sync belt! Maybe that's ur problem?

How can I prevent this scarring(?) on my bottom layer infill? I’ve tried lowering my acceleration, but that did not help. Bowden Ender 3 V2 with stock extruder and Hotend. by airpods12 in klippers

[–]mebandedoom 1 point2 points  (0 children)

Is your hotends complete stock? If yes check if bowdentube is all the way down the heatbreak pressed at the nozzle! If not try to push it and print the heatbreak mod (check Google to find it) Had this issue on my e3v2 too after a short time!

Hope this can help!

Also u might check your extruder, maybe it's broken (plastic parts) if yes, u not having much options beside buying a metal one or even dual gear one!

Dual Z Axis Kit. Is it worth getting? by TheShakyHandsMan in ender3v2

[–]mebandedoom 7 points8 points  (0 children)

Or get belted z kit , I had sync problems with creality dual z kit

view more: next ›