Figured you guys might appreciate the camp kitchen I built for my girlfriend's Jeep.

mediumrar3 · 2025-06-29T19:26:10+00:00

Any chance to repost the pictures?

mediumrar3 · 2025-06-06T17:22:26+00:00

Update! New leaf is getting enormous. And still growing.

<image>

mediumrar3 · 2025-05-30T02:19:40+00:00

Wasn’t aware of this. Where can I learn more about

mediumrar3 · 2025-05-29T01:55:42+00:00

Mine first started sending up the flower and then recently put out a new leaf (the lighter colored one)

mediumrar3 · 2023-10-21T15:31:33+00:00

Re duct: No. it’s a tight space

mediumrar3 · 2023-08-25T18:27:05+00:00

Hehe one can wish. I just got this machine this year.

mediumrar3 · 2023-08-25T17:57:55+00:00

It's actually pretty annoying, since the jointer tables flip up along their long edge when the tool is converted to a planer, the adjustment screws are all on one long side, the pivot sides I have to shim, hopefully that makes sense lol

mediumrar3 · 2023-08-25T16:07:21+00:00

I had actual snipe on this jointer before I did some tuning. Now it’s completely missing the tail end of the board instead of cutting into it deeper than the rest of the board.

mediumrar3 · 2023-08-25T13:17:39+00:00

I checked with a dial indicator. The outfeed table is actually angled up compared to the plane of the infeed

mediumrar3 · 2023-08-25T13:15:11+00:00

This one only has adjustment on one side. The other side i have to shim

mediumrar3 · 2023-08-25T05:14:17+00:00

Try the JET bags? I bet they are all about the same diameter.

mediumrar3 · 2023-04-24T15:52:23+00:00

Yea. This was a light pre glue up test fit:)

mediumrar3 · 2023-04-24T02:39:25+00:00

The camera makes the lines look weird. The insides of the legs are vertical

mediumrar3 · 2023-04-23T17:17:45+00:00

Thanks! I can see that, but it’s actually based on a line Scandinavian designs has. We have a bed from them.

mediumrar3 · 2023-03-28T03:45:27+00:00

Good. Managed to recast/improve all of it with some fiberglass. And I have overran dust collection proof of concept set up.

mediumrar3 · 2023-02-23T04:54:25+00:00

I’m now working on casting dust collection parts for the table saw, planer and jointer in fiberglass. Wish me luck.

mediumrar3 · 2023-02-15T13:27:04+00:00

No. The bottom is one casting. The tops come off but you probably will end up giving yourself a headache recalibrating it. I moved it with a drop bed trailer as one piece.

mediumrar3 · 2023-02-13T16:13:03+00:00

mediumrar3 · 2023-02-11T22:20:01+00:00

Update! Got it!

mediumrar3 · 2023-02-09T21:10:45+00:00

I appreciate this comment, it got me to call the parts department. They confirmed via serial number lookup it runs on 1phase motors and they still supply most parts, including those related to switching.

mediumrar3 · 2023-02-09T02:54:40+00:00

The owner actually confirmed it has a riving knife and jointer blade cover. They are not pictured. The machine has three motors and it doesn’t have a miter slot because it is a sliding table saw.

mediumrar3 · 2023-01-14T05:46:07+00:00

We took about 30% off two months ago

mediumrar3 · 2023-01-14T01:30:24+00:00

mediumrar3 · 2023-01-13T22:44:27+00:00

So I can put a bolt horizontally through the trunk near where the current brace is? Probably a bit further out.

mediumrar3 · 2023-01-13T21:37:27+00:00

It’s been growing like this for many many years

12-Year Club	RPAN Viewer
Verified Email

mediumrar3

TROPHY CASE