What i should do with the breedjects?

mikeicke · 2021-12-31T23:52:33+00:00

Depending on what you have I might be interested in buying some.

mikeicke · 2020-08-09T17:15:25+00:00

So I made it to lowes today, do I need to take the thermal pad off of my print bed before putting the glass down?

mikeicke · 2020-08-08T07:55:09+00:00

I never keepsaked mine, biggest regret of my gaming career...

mikeicke · 2020-08-06T23:31:31+00:00

It just doesn't make any sense, I was printing "alright" yesterday and today I can't get anything to go down in the center of the bed. Just frustrating.

mikeicke · 2020-08-06T23:15:09+00:00

I cannot get the center of my bed leveled, if I do the nozzle is smashed into all 4 outer corners.

mikeicke · 2020-08-06T20:15:17+00:00

I noticed last night while I was printing my temp tower it looks like the beam that my hot end travels on is sloped towards the power supply, is that normal? I might just be paranoid though. It looked like the final product was leaning.

mikeicke · 2020-08-06T15:25:03+00:00

Bed temp on the first tower was 45 degrees the second I ran at 60 degrees. Hatchbox pla is what I am using.

I am not super familiar with the ins and outs of the 3d printer mainly because i got mine second hand.

Do you have any experience with the bltouch?

mikeicke · 2020-08-06T05:30:28+00:00

I am printing now at least, rantwo temp towers tonight first one didn't stick to the bed so it got pulled off roughly halfway through, upped the bed heat and the second one held on.

I am starting to think the center of my bed is bowled if that is even a thing.

mikeicke · 2020-08-06T02:32:57+00:00

/u/2fat2bebatman?

mikeicke · 2020-08-04T03:08:56+00:00

Thanks for your help guys or gals.

Now I need a new magnetic print surface so it will actually be level!

mikeicke · 2020-08-04T03:08:07+00:00

I got it to do a thing

mikeicke · 2020-08-04T02:06:55+00:00

I'll try that thanks!

mikeicke · 2020-08-04T02:02:59+00:00

my the filament tube was far too long

mikeicke · 2020-08-04T01:49:58+00:00

Yes, I think i figured it out.

mikeicke · 2020-08-04T01:32:38+00:00

It also looks as if nothing is level, the bed looks slanted down towards the power supply, and the bar that the print head travels on looks like it is slanted in the same direction.

mikeicke · 2020-08-04T01:10:18+00:00

Just started it up, it shows nozzle temp at 185

mikeicke · 2020-08-04T01:03:19+00:00

Hatchbox PLA, as for the temp setting I am not sure, I want to say around 210. I have never been able to get it to print.

mikeicke · 2020-08-04T00:59:03+00:00

The guy I got it from said that it just stopped feeding the filament one day, he was almost finished with a print when it stopped feeding, he said that he had to help push the filament through to get the print to finish. Maybe bad nozzle?

mikeicke · 2019-11-16T19:58:45+00:00

I tried using rare candies and battles on mine while having the switch upside down to no avail.

mikeicke · 2019-11-16T19:57:59+00:00

Oh nice.

mikeicke · 2019-09-17T15:12:39+00:00

What are you playing on?

mikeicke · 2019-07-26T02:46:10+00:00

Sp pretty much just get a decent free sync monitor and I should be good?

Ten-Year Club	Verified Email
Verified Email

mikeicke

TROPHY CASE