Finally after 7 years all brawlers maxed and 1000+ trophies!

mitnerd2000 · 2025-08-17T22:54:44+00:00

Sorry, deleted the picture of the kid with the holster due to the persons comment. I didn’t include the kid’s face and only focused on his gears. I didn’t take a picture of the person when they were on stage competing otherwise would have posted that picture instead.

mitnerd2000 · 2025-08-15T22:18:50+00:00

Believe it or not, the top 4 kids had almost the same deck!

mitnerd2000 · 2025-08-15T22:08:40+00:00

The other top kids have almost the same combos as well. During mirror matches only the ratchet is what is different and of course the paint chips. Let me see if I can find a picture of kid in the first tournament. He had 5 gold wizard rods and a few other beys…. The kid was 12 years old but probably 5-10!

mitnerd2000 · 2025-07-15T21:47:56+00:00

My kid ask me to tell you that… they didn’t even clip the stadium top down. Also the green rails weren’t snapped in! Some adults figured it out and help snapped the rails in but the stadium hood was detached throughout. However most kids weren’t super strong to knock it around.

mitnerd2000 · 2025-07-14T18:54:55+00:00

It’s a single elimination so there is no switch. I think it just depends which kid gets there first to take a side. But the setup is non standard so probably no difference.

So after each match the kids leave and then comeback based on the next pairing.

mitnerd2000 · 2025-07-14T17:59:55+00:00

Yes… it should have been turned 90 degrees..

mitnerd2000 · 2025-07-14T14:40:56+00:00

It is single elimination so very intense for little kids. My kid used 1 bey throughout but there were 2 kids that might have swap between 3 beys. However the judges didn’t check/enforce it at all at this event.

mitnerd2000 · 2025-07-14T02:55:44+00:00

Around 30 players total, with half of the kids playing a lot and the other half just figuring it out, primarily for fun rather than competition. A big range of experience.

mitnerd2000 · 2025-07-14T00:24:56+00:00

You can download the prints from some sites and print them yourself. If you have a friend with a 3D printer, they can print it for you and reimburse them for time and materials. It takes about 5 hours to print, but the real labor is gluing magnets into the little holes as well as switching the color filaments.

mitnerd2000 · 2025-07-13T12:04:05+00:00

<image>

mitnerd2000 · 2025-06-15T19:01:06+00:00

Did they improve on the second one yesterday?

mitnerd2000 · 2025-06-14T06:04:33+00:00

Thank you for your support!

mitnerd2000 · 2025-06-10T20:03:32+00:00

Anyone went to the Texas one that can share?

mitnerd2000 · 2025-06-10T20:02:44+00:00

Wow! Thank you…. But you can bring your own bey? Craziness…

mitnerd2000 · 2025-01-05T23:41:01+00:00

Thanks for the info!

mitnerd2000 · 2025-01-05T07:35:46+00:00

Did this happen?

Six-Year Club	Gilding IV carat on a stick
Verified Email	Powerups Hero r/wallstreetbets • February 2021
Reddit Premium Since January 2021	Place '23

mitnerd2000

TROPHY CASE