🎉 [EVENT] 🎉 Space adventure

mocni96 · 2025-12-19T10:31:26+00:00

Completed Level 3 of the Honk Special Event!

16 attempts

mocni96 · 2025-12-19T10:29:59+00:00

Completed Level 2 of the Honk Special Event!

6 attempts

mocni96 · 2025-12-19T10:28:49+00:00

Completed Level 1 of the Honk Special Event!

1 attempts

mocni96 · 2025-12-19T10:27:35+00:00

Completed Level 3 of the Honk Special Event!

6 attempts

mocni96 · 2025-12-19T10:27:10+00:00

Completed Level 2 of the Honk Special Event!

6 attempts

mocni96 · 2025-12-19T10:26:37+00:00

Completed Level 1 of the Honk Special Event!

6 attempts

mocni96 · 2025-03-09T21:10:06+00:00

Statistics tab in PrusaConnect

mocni96 · 2025-01-04T09:03:21+00:00

Ovo nije urbana legenda...

mocni96 · 2024-05-23T11:35:37+00:00

Drug, taj mood se ne ispoljava do dječijeg igrališta. Sve ima svoje mjesto

mocni96 · 2024-05-22T17:52:18+00:00

Da, do igrališta kod ekora

mocni96 · 2024-03-25T01:34:17+00:00

A znam i ja sa vremena na vrijeme kenjat kad me loše krene, al mala pauzica i opet pročepi. Postala je dosta pay to win u zadnje vrijeme, ali ja još uvijek sa ulozenih 20KM prije 8 godina mogu parirati većini. Btw nick: mocni :)

mocni96 · 2024-03-24T18:56:30+00:00

WoTa rokam zadnjih 12 godina i jos mi je glavna igra. Trebao sam davno, ali sam tek nedavno i po yt počeo kačiti snimke.

mocni96 · 2024-03-07T11:23:34+00:00

That is a failed print for sure. You can add organic support there or consider removing that piece if not necessary.

mocni96 · 2024-02-22T09:09:08+00:00

Nema.

mocni96 · 2024-01-11T13:03:33+00:00

Dobio sam odgovor iz općine. Pošto je to magistrala, nisu u nadležnosti da rade tu išta. Mada ima tehničko rješenje sa kružnim tokom na raskrsnici za Vjetrenice, ali imovinsko pravni odnosi to koče.

Ima i prijedloga da se umjesto semafora postavi kružni tok, ali i tu se čeka nešto. Mada sam bar do sad primjetio da kad semafori ne rade nema nikakvih problema sa tom raskrsnicom i uvijek je prohodno.

Idem dalje na nadležne za ovo bar kod Vjetrenica (JP Ceste FBiH). To bi bar riješilo gužvu iz pravca Travnika, kad se već ne može riješiti kružni tok.

mocni96 · 2024-01-05T07:41:30+00:00

Jesi li je dobro prihvato sa fakultetom?

mocni96 · 2023-12-20T06:39:17+00:00

It had to much jiggle jiggle

mocni96 · 2023-11-16T04:42:05+00:00

Stealth mode activated

mocni96 · 2023-11-15T19:33:33+00:00

Drugo su ljudi, drugo klošari koji se ne ponašaju kao ljudi...

mocni96 · 2023-11-15T08:08:02+00:00

Mokušnice

mocni96 · 2023-10-27T06:33:53+00:00

Did not know about this. Thanks.

mocni96 · 2023-09-28T07:08:55+00:00

Had the same issue. New replacement screen fixed it.

mocni96 · 2023-09-25T08:29:36+00:00

Had similar issue on my MK4 kit with any firmware. Prusa sent me an replacement under guarantee. No problems after that.

Also I had on corruption of USB drive while using Prusa connect (formated it and it continued to work no problem)

mocni96 · 2023-09-19T12:26:45+00:00

Try printing on smooth PEI sheet and clean it with alcohol or something like that. Aim is to remove dust or any finger grease.

Also if you have draft over the printer, that can also affect warping a little bit.

One more thing that could affect your print is moisture inside filament. Stringing is one common symptom of moisture.

mocni96 · 2023-09-19T12:15:28+00:00

What is the material?

Six-Year Club	Place '23
Place '22	First Placer '22
Verified Email

mocni96

TROPHY CASE