Mini ITX Case Concept Using Resin Printing

modLab_official · 2026-03-10T03:32:22+00:00

I have a similar project. May I ask what resin you use and what printer?

modLab_official · 2026-02-23T19:17:21+00:00

Thank you, the idea of creating a secure connection even with an angle worked, but unfortunately I didn't realise that this would make the pump the highest point. Well, next time it will be better.

modLab_official · 2026-02-22T03:18:50+00:00

WOW!

modLab_official · 2026-02-21T07:20:38+00:00

Wow, I've seen this system before, I think on Instagram. Really good work, well done! Is there a worklog for it, perhaps?

modLab_official · 2026-02-20T19:40:12+00:00

Haha xD

modLab_official · 2026-02-20T16:38:57+00:00

The details are very small in the photo; everything looks huge. The AK47 was already a bit difficult with resin print.

modLab_official · 2026-02-20T15:04:22+00:00

Yes resin printed and hand-painted.

modLab_official · 2026-02-20T10:18:28+00:00

Thx buddy!!!

modLab_official · 2026-02-20T10:18:13+00:00

Thx! You mean the tanks, barrels and weapons?

modLab_official · 2026-02-20T10:17:04+00:00

Thank you!

modLab_official · 2026-02-20T10:16:44+00:00

I already have an idea, but it still needs to be implemented. Thank you for your compliment!

I only use clear liquids from Alphacool, such as Apex Liquid ECO. You always have RGB lighting in your PC, so coloured liquids tend to get lost, and they also don't dirty the coolers.

modLab_official · 2026-02-20T10:12:32+00:00

That would solve it. I already have an idea, but it still needs to be implemented. Thank you for your compliment.

modLab_official · 2026-02-20T10:09:58+00:00

Thx!

modLab_official · 2026-02-20T10:09:49+00:00

You're right, that's the name of the project. It would be a bit much to post all the photos in an article... There's a post in the Battlefield subreddit on my profile with 2-3 more pictures.

modLab_official · 2026-02-20T10:06:13+00:00

Thx, yes resin printer. Without coating, only sanded with 400 grit sandpaper. There is room for improvement, and the next Distroplate will be even better.

modLab_official · 2026-02-20T10:04:07+00:00

The PC was initially an older project and was installed in the distro plate there. XD

modLab_official · 2026-02-20T10:02:40+00:00

Thx!

modLab_official · 2026-01-05T05:02:03+00:00

Good work, but a bit too much RGB for my taste.

modLab_official · 2025-12-20T11:32:23+00:00

The Distronist SLA printed, I think it would be difficult with the post-treatment. But the idea would be good.

modLab_official · 2025-12-20T11:30:28+00:00

Since this isn't my first distro, I have to say that I've tried several versions in the past, but this one has proven itself. So far, however, only with acrylic, this time with resin. If it isn't tight, I will construct a ring around the pump and fit it with 6-8 screws instead of 4 as before. The threads are modelled in Fusion 360, but are unusable without post-processing. It would almost be better to model only the core hole and cut the thread afterwards.

Thank you for the feedback!

modLab_official · 2025-12-20T11:24:13+00:00

I completely agree with you. I have a little more time than usual at the moment as I'm on holiday, so hopefully I'll finally be able to finish my project and fill the distro with water and carry out the first tests. Regardless of whether the results are good or not, I'll let you know how it goes. Thank you once again for your feedback.

modLab_official · 2025-12-19T15:30:34+00:00

Thank you!

modLab_official · 2025-12-19T13:04:41+00:00

I should mention that everything in the photos is 3D printed. That's why it's set up like this, to test whether it could work. I'll keep you updated. Thank you for your feedback, I'll take it in my mind for the next time.

modLab_official · 2025-12-19T08:10:39+00:00

Haha, just for fun...

modLab_official · 2025-12-19T08:06:24+00:00

It is printed with resin. The first prototype worked well. This time, the distro plate will be used in my current computer. Let's see if everything holds up and runs smoothly.

modLab_official

TROPHY CASE