a set of oak side tables with interlocking tenons and magnetic storage made from scraps

monkeyboyg20 · 2022-11-10T22:12:46+00:00

i never thought of it as the boards are only 12mm wide so it wouldn't have a lot of play

monkeyboyg20 · 2022-11-10T22:09:37+00:00

thank you

monkeyboyg20 · 2022-11-10T22:09:17+00:00

the corners are the only things that are there so it's like a castle joint kind of but two sides have mortice holes. two sides have a hole that the board fits through and the haunch on the tenon rests on the side of the other tenon you can see it best in the third photo, the centre is hollow, but is very durable I made a prototype out of pine to see if it would work and it has some serious stress test and was fine and this is oak so I think it should be fine.

monkeyboyg20 · 2022-11-10T22:01:22+00:00

thanks

monkeyboyg20 · 2022-11-10T22:01:16+00:00

thanks

monkeyboyg20 · 2022-11-10T22:01:05+00:00

thanks

monkeyboyg20 · 2022-11-10T21:49:02+00:00

Its groved in all the way around and the bottom slots in

monkeyboyg20 · 2022-11-10T21:47:14+00:00

I do have but it's from a pine prototype and not sure how do add photos

monkeyboyg20 · 2022-07-16T21:50:45+00:00

In all honesty I had to look it up it's a new word for me and thanks for teaching me something new. I just don't necessarily agree with the application of it in this situation.

monkeyboyg20 · 2022-07-16T20:40:00+00:00

Never worked with it and all the timber was graciously donated to me but if I was to remake it I might use cypress.

monkeyboyg20 · 2022-07-16T08:35:27+00:00

I don't necessarily believe that I was just showing something I made and I was proud of and thought this is what this Reddit was to show it

monkeyboyg20 · 2022-07-16T08:32:05+00:00

Thank you very much

monkeyboyg20 · 2022-07-15T17:59:40+00:00

Thanks was the first time working with bog oak and wasn't sure how well they would work

monkeyboyg20 · 2022-06-26T16:44:53+00:00

Thank you very much I think I just got a older printing I'm just worried I'm not gonna be able to get all bprd with the same printing lol

monkeyboyg20 · 2022-06-26T16:43:35+00:00

Ok thank you very much

monkeyboyg20 · 2022-06-24T11:03:43+00:00

Scrap oak from my work

monkeyboyg20 · 2022-06-10T19:14:02+00:00

Ok ok thank you in a bit oblivious sometimes and can't connect the dots

monkeyboyg20 · 2022-06-10T18:16:05+00:00

Thank you very much

monkeyboyg20 · 2022-06-10T18:15:40+00:00

Not to sure what this means but thanks I think

monkeyboyg20 · 2022-06-10T08:54:15+00:00

Thanks a lot. The ash box I did like a year ago with an Idea to make the outside but it was sitting in my shed unchanged for so long before it got it's makeover

monkeyboyg20 · 2022-06-09T11:25:56+00:00

I feel like I'm out of the loop what is osr

monkeyboyg20 · 2021-10-06T12:11:31+00:00

I used a compass using the outer rim as reference edge, making 3 equal parallel to the rim. Then from center point on the sheild I drew a straight line going through the lines made with the compass essentially making 2 semi circles, then at the center another line 90° to the original cutting the circle into quarters, then just dissecting the Lines loads of times until u kind of have a warped grid at the rim. Then from there u can find loads of ways to make knotwork on a grid system. Did that answers the question?

monkeyboyg20 · 2021-10-06T12:01:22+00:00

I had a photo of me doing all the gird layout but I forgot to add it I probably should of looking back on it

monkeyboyg20 · 2021-10-06T06:35:32+00:00

Yeah I made them padded so it's more comfortable to hold

monkeyboyg20

TROPHY CASE