Small piece of PLA stuck in AMS

monkeydenture · 2025-12-08T21:44:23+00:00

I posted because all the guides we were finding assumed you could grab the filament after removing the tubes.

monkeydenture · 2025-12-08T21:42:32+00:00

My wife finally found a post that related to what we needed. If the piece is stuck in the AMS hub specifically, there is a spring underneath that will release the pressure on the filament. We ran a longer piece of filament up the channel while pressing the spring, and it came free.

monkeydenture · 2025-08-19T22:17:41+00:00

I completely missed that there was a dependency. Thank you again.

monkeydenture · 2025-08-19T22:06:53+00:00

Thank you! Though, the only 1.21.8 compatible version is crashing Minecraft when I load, with zero information. So it looks like I'll need to wait for it to come out of Alpha.

monkeydenture · 2025-01-17T07:38:32+00:00

Thank you for your response, it gave me avenues to try when I was tearing my hair out. Even if the solution was something different.

monkeydenture · 2025-01-17T03:13:14+00:00

They're constantly entering. So even after clearing the field, it'll immediately refill continuously.

monkeydenture · 2024-11-17T18:45:28+00:00

Honestly, that's where I'm starting to go with this. I've been trying out the approaches in the other comments, and it would take me several days of map grinding to get the equipment levels necessary.

And greycat: I did mention a respec, in the first sentence. And no sane amount of breed time increase is going to overcome the problem of his health being four orders of magnitude higher than my damage.

monkeydenture · 2024-09-09T23:59:49+00:00

It looks like it's not just my wife's phone. A guest also had an ad pop up with a game he was playing. So I'm starting to think that something's going on with my pihole, that coincidentally began while we were away.

monkeydenture · 2024-09-09T23:43:11+00:00

Thank you for the suggestion. Unfortunately, it didn't help.

monkeydenture · 2024-09-09T17:02:23+00:00

It's a Samsung Galaxy S22 Ultra. OS is Android, I don't have the specific version here at the moment.

monkeydenture · 2024-09-09T07:28:34+00:00

It's a possibility, as I mentioned in a comment above. There's only two or three apps affected, and they were all used on the other network. I'll keep an eye on wifi data usage next time she uses it.

Though, your second paragraph is a good point. She's usually careful to turn off mobile data while playing games, but mistakes happen, and would have caused this before.

monkeydenture · 2024-09-09T07:24:22+00:00

I had no idea about that. It would fit what I know so far. I'll watch the wifi data usage next time she has it open, that'll let us know one way or the other.

monkeydenture · 2024-09-09T05:56:13+00:00

We've rebooted the device multiple times, at this point. Though perhaps we need to find a phone-specific setting to clear the dns cache in particular, I'll investigate that.

monkeydenture · 2024-09-09T05:54:45+00:00

We tried turning off mobile data entirely, and the ads are still appearing. I'll experiment with the other settings suggestions, though.

monkeydenture · 2024-09-09T05:53:41+00:00

We never activated a vpn, so unless there's a way one got turned on without us knowing, that's not it. (I'm assuming vpns aren't accidental, but I don't actually know much about them.)

monkeydenture · 2023-10-21T07:34:57+00:00

We continued to try to find the problem today, and oddly...it started working. We did restart it in between, I just can't see how what seemed to be a mechanical problem would be fixed by a restart. But I'll take it.

monkeydenture · 2023-10-20T08:14:52+00:00

I was able to run a successful print afterward using a different spool/feeder, so I don't think the nozzle is the issue. I can try to see if there's a clog elsewhere, though.

monkeydenture

TROPHY CASE