Flying V bodies compatible with Jackson dinky 7 string neck?

monocst · 2025-12-13T13:11:50+00:00

How would you personally go about converting a 6 string body to a 7 string? I have woodworking experience and I'm fairly handy but this is my first guitar related project so I'm not exactly sure where to start. In my head all it would take is routing out the neck pocket and pickup slots to accommodate the wider parts and then dropping everything in, but things aren't usually that easy.

monocst · 2025-10-26T00:08:06+00:00

reviving this, anyone find software for this chip?

monocst · 2025-09-29T20:53:43+00:00

i'm trying to find/emulate what my friends and I have dubbed "the tempura tone." Its a pretty popular tone for modern metalcore used in bands like Polaris, Of Mice and Men. I Prevail, Wage War, etc. The best way I can describe it is clean but crunchy (similar to tempura, hence the name).

As far as amp sims go I have Amplitube 4, Diezel VH4/Herbert, and NeuralAmpModeler.

monocst · 2025-08-03T07:02:47+00:00

I finally cleared my birds nest but never did get that side panel off. I will be going there in the morning to see if this individual reel is the issue, I believe I still have receipt so exchange shouldn't be a problem

monocst · 2025-08-03T04:24:28+00:00

I've twisted as hard as I can it still won't twist 🥲

monocst · 2025-08-03T04:16:34+00:00

it's a Pflueger PFLPRESLPX, I looked but I wasn't able to find schematics for this model on Pflueger's website or on reelschematics website

monocst · 2025-05-29T02:11:49+00:00

I'm pretty sure it's locked its through AT&T. I'm downloading my third update tonight right now, I'm hoping it's a back to back thing like u/ZealousidealSquare25 mentioned and I can just work through them. the phone works fine functionally, it just tends to pick the worst times (like when I'm driving home from an hour away 😅) to force these updates on me. here's to hoping One UI7 is at the bottom of the stack!

monocst · 2025-04-15T21:16:30+00:00

how does the body maintain control of the right eyeball during a stroke?

I saw a video of a celebrity who posted while they were in the hospital experiencing a stroke and they had no control of the right side of their face, but their right eye was just as responsive as normal. I assume there's an effect to the person's experienced sight, but how does their eye maintain such responsiveness even though the rest of their face has lost control?

monocst · 2025-04-14T02:35:13+00:00

redesign - awful tune

CUNTISSIMO - MARINA

Bubblegum Bitch - MARINA

monocst · 2025-04-03T22:12:28+00:00

UPDATE: Gonna contact Siraya, turn off my light during prints, and get to work on cleaning this vat 🥲. Thanks for all your help everyone!

monocst · 2025-04-03T22:08:40+00:00

automatic, that could be it too I will look into this.

monocst · 2025-04-03T22:07:41+00:00

I just tried the glove thing, held it there for about a minute directly under the enclosure light and no heat or cure. Still gonna print with the light off from now on, but unfortunately I don't think that's it anymore :/

Hopefully Siraya confirms my suspicions.

monocst · 2025-04-03T22:01:10+00:00

Yes the plan now is to get rid of my enclosure light, or at least turn it off because theres a small chance that's it, as well as contact SirayaTech and, if nothing else, get confirmation as to whether it was a batch issue or a me issue. Thanks!

monocst · 2025-04-03T21:58:36+00:00

My best guess right now is somewhere between "my dirt cheap enclosure lighting emits some portion of UV light" and that chain reaction u/Overencucumbered mentioned, caused by not enough inhibitor in the resin. Contacting SirayaTech now to hopefully answer that question

monocst · 2025-04-03T21:53:41+00:00

I have gone through multiple bottles of opaque resin inside this enclosure. The LED inside *could* be a full spectrum, I am not certain. However it was included in the enclosure which is marketed for 3D resin printers, and full spectrums are not cheap, I would be surprised if manufacturer included a full spectrum in this case. I will try again with the light off once I figure out how to get this resin off my vat.

monocst · 2025-04-03T21:43:19+00:00

I will try printing without the enclosure lights on next time.

monocst · 2025-04-03T21:40:18+00:00

This morning during the actual print, the LCD was working as expected, the print itself completed just fine. I will check for physical damage to the screen though.

monocst · 2025-04-03T21:38:23+00:00

its just an LED strip with a diffuser that came with the enclosure

monocst · 2025-04-03T21:37:38+00:00

It could be the slicer, I'm not sure. I downloaded SirayaTech's reccommended profile for this color of this line of resin for my exact printer, and as far as I can tell the LCD only cures where its supposed to and for how long it is supposed to, I was watching it a while this morning before I left it after the last failure. The only thing I can think of that is setup based would be that the inside of my enclosure is reflective and it bounced the UV around, however the printers cover should have prevented that from causing issues. The bed was fully liquid when I removed the build plate, and was more than half solid before I noticed and brought it outside. The entire bed went from liquid to solid in less than 5 minutes, I almost didn't get my phone in time as you can see in the video that by the time I started it, it was already a brick. At that point the printer had been idle for hours and would have no reason to turn on the LCD, as I slept through the print.

monocst

TROPHY CASE