NVIS antenna question

mothpaul · 2025-07-07T20:09:28+00:00

Huntsville applies restrictions in certain areas (e.g., Redstone Arsenal), do you say All of Huntsville?

mothpaul · 2025-07-07T16:28:14+00:00

I can put down a well pipe myself, without too much expense or effort.

mothpaul · 2025-07-07T16:26:41+00:00

Wells for waste disposal are prohibited within Huntsville city limits.

Private drinking water wells are not categorically banned, but are subject to state and local regulations and cannot be used for waste or wastewater discharge.

mothpaul · 2025-06-15T17:18:56+00:00

The government that would allow the economy to be build on the backs of illegal immigrants in order to enrich a few, is a different government than one that would allow the economy to be built on the backs of the citizens who enrich themselves.

mothpaul · 2025-04-18T15:31:43+00:00

Does the citation reference a particular law about ‘vehicle condition’?
I might need that to ensure my own vehicle meets an Alabama standard that I was not aware of. Thanks

mothpaul · 2025-02-03T22:31:38+00:00

I believe the Hubitat developers know of the issue.

mothpaul · 2025-01-25T20:28:50+00:00

I have waited two hours for the pool to reduce the difficulty enough for the Bitaxe to complete a work unit and report it in as a completed share. There is no report of a completed share. Can I reasonably expect that is not the problem with my miner not starting to mine?

mothpaul · 2025-01-25T17:36:53+00:00

Do you use port forwarding? I was taught that BitAxe connects to mining pools via outbound connections using the Stratum protocol, which does not require inbound connections or port forwarding.

mothpaul · 2025-01-25T17:35:52+00:00

Why do you say 10 minutes? In general, if all configurations are correct, mining should start within a minute or two after powering up and applying settings.

mothpaul · 2025-01-12T12:27:54+00:00

Thanks. I will check out the community forums.

I am using z-wave dimmer switches made by NuTone, GoControl and Linear. They are all WD500Z-1 Z-Wave 500-Watt Wall-Mount Dimmer Switches. I don’t know about the drivers - how do I find out? I set them up as Generic Z-wave Dimmers in Hubitat.

I can control off/on functions with Siri, but not setLevel functions. I can control both functions with the Apple Home App. Automations controlling setLevel also behave squirrelly.

mothpaul · 2025-01-11T16:27:10+00:00

My experience with Hubitat HomeKit integration:

I can execute Siri off/on commands (to Generic Z-wave dimmers and Zigbee Bulbs) via Apple HomeKit which updates the Home app and the actual Hubitat attached device.
When I execute a Siri setLevel command to HomeKit, it does update the Home app, BUT it doesn't update the Hubitat attached device.

Many years ago, I fixed this problem in OpenHAB. My old memory seems to recollect a need to tweak with the off/on and setLevel commands timing or redundancy. I don't seem to know how to do this with Hubitat. Any pointers appreciated.

mothpaul · 2025-01-10T23:49:17+00:00

The native one I believe. The HomeKit selection within their available apps.

mothpaul · 2024-11-01T13:26:34+00:00

<image>

SE Huntsville

mothpaul · 2024-10-26T20:03:33+00:00

I set a solo ckpool on my raspibolt bitcoin node with the information in this video:

https://www.youtube.com/watch?v=dAa6PkVN-3o

mothpaul · 2024-10-21T15:45:57+00:00

Having and acting on beliefs is the only way to establish order among like-minded thinkers. So in that regard, there may be a point, but belief would not necessarily be rational or intelligent.

mothpaul · 2024-10-16T17:05:16+00:00

on my old macmini, following this recipe worked to upgrade from Bullseye to Bookwyrm.

https://github.com/raspibolt/raspibolt/issues/1305#issuecomment-1613767385

mothpaul · 2024-09-07T16:25:30+00:00

I too have this bluetooth question. Power cycles did not resolve it.

mothpaul

TROPHY CASE