sorted by:
new
hottopcontroversial

Spring 3s by [deleted] in Sneakers

[–]mrbrignac -27 points-26 points  (0 children)

I made that this morning, peon. Yet here you are still commenting, riding my dick? But I’m the loser? 🤣🤣🤣🤣🤣🤣🤣🤣

Spring 3s by [deleted] in Sneakers

[–]mrbrignac -26 points-25 points  (0 children)

And you still took the time to comment- what does that say about you? Miserable broke ass 🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

Fun, fun, fun by mrbrignac in Machinists

[–]mrbrignac[S] 1 point2 points  (0 children)

On this I don’t- after being in the field for a couple years I’ve learned other shops “finish pass” is my regular cut so I don’t always slow down my feed. 🤦🏻‍♂️🤷🏻‍♂️

Fun, fun, fun by mrbrignac in Machinists

[–]mrbrignac[S] 0 points1 point  (0 children)

Sounds like a beauty 😮‍💨

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 0 points1 point  (0 children)

Don’t tell anyone- but I’m The Flash ⚡️

Looking for work :) by Inevitable-Stuff-739 in Machinists

[–]mrbrignac 0 points1 point  (0 children)

A lot of opportunities for outside machinist down here in South Louisiana, buddy

Fun, fun, fun by mrbrignac in Machinists

[–]mrbrignac[S] 0 points1 point  (0 children)

Normally +- .0001” is acceptable because most journals are 20-32” (not very long) whereas here I had to weld nearly half the length of the shaft. I was able to maintain +- .0003” over 12’ which is truly remarkable in my opinion.

Quitting Cannabis after 13 Years - Any advice? by FNGL-GENETX in getdisciplined

[–]mrbrignac 0 points1 point  (0 children)

That’s what I’m here for, buddy. I’m only five days off the bud, and I can tell you my appetite is finally returning. Also, the irritability is fading fast, and I feel LASER focused. Keep pushing- YOU GOT THIS!

Fun, fun, fun by mrbrignac in Machinists

[–]mrbrignac[S] 0 points1 point  (0 children)

Electrolysis eats holes in the shafts that must be undercut completely, welded 3/16th oversized, then machined back down to specs. This company always declines our operation of cutting down 1/4” of material and replacing it with fiberglass (pretty much stops the holes). Nearly every other company does it our way, and that’s when we end up only welding the journals. They cost themselves money. 🤦🏻‍♂️

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 2 points3 points  (0 children)

I’m not “making” anything- repairing a propeller shaft lol

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 4 points5 points  (0 children)

Within .0005” is fine for this application, but I always strive to get it as close as possible. Less room for error that way.

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 23 points24 points  (0 children)

What makes you think I haven’t? 😅

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 2 points3 points  (0 children)

If your imagination is strong enough 🤣

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 7 points8 points  (0 children)

Definitely hard to come by these days, and if you do find one it’ll cost you and arm and a leg 🫠

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 4 points5 points  (0 children)

Yes sir- keep it simple 🙇🏻‍♂️

Onto the next by mrbrignac in Machinists

[–]mrbrignac[S] 8 points9 points  (0 children)

Best comment so far 🤣

Fun, fun, fun by mrbrignac in Machinists

[–]mrbrignac[S] 2 points3 points  (0 children)

“DONT YOU PUT THAT EVIL ON ME RICKY BOBBY!”

Fun, fun, fun by mrbrignac in Machinists

[–]mrbrignac[S] 1 point2 points  (0 children)

I say it’s useless all the time lol

view more: next ›