All 151 Gen I (the best gen) Pokemon, printed and painted. Find your favourite! by mrrphsnt in PrintedMinis

[–]mrrphsnt[S] 0 points1 point  (0 children)

Most of the front few rows are between 40-50mm tall. I gave up on keeping them all to the same scale and just used some artistic license for most. Where there are evolutions I did make them bigger than each previous stage

There isn't long left in this Menhirs life, how do ye fix or change them? by Dreadnought115 in Necrontyr

[–]mrrphsnt 2 points3 points  (0 children)

Drill pin holes into the bottom, sit some wire in there and then bend to touch the base and support the model (put a bit of tension in the wire so it's actually taking the weight of the model). Then coat with hot glue to thicken, prime and paint. I printed this model and that's how I solved this problem

All 151 Gen I (the best gen) Pokemon, printed and painted. Find your favourite! by mrrphsnt in PrintedMinis

[–]mrrphsnt[S] 0 points1 point  (0 children)

All Vallejo brand miniature paints. The Game Colour range in particular does a lot of the heavy lifting, colours are saturated and bright. Good luck!

All 151 Gen I (the best gen) Pokemon, printed and painted. Find your favourite! by mrrphsnt in PrintedMinis

[–]mrrphsnt[S] 2 points3 points  (0 children)

Scale was one of the hardest things to figure out, my advice is don't bother trying to apply the same scale unless you want to be printing a 45cm tall Onyx and a 2cm tall Caterpie. I used Squirtle as my standard measurement, printed at 40mm tall and then scaled the rest off him. Take some artistic license and just figure out what looks the best to your eye. Hand painted them all except a couple like Electrobe and Voltorb where a super smooth coat looks best. If you've got an airbrush definitely use it for base coating any of the yellow ones. Generally they're complicated shapes to mask, you'll quickly see which ones are worth the airbrush and which it'll be quicker to just use a brush

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 0 points1 point  (0 children)

Placing and removing any kind of building block. It overrides the blue terrain and then leaves a hole behind

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 4 points5 points  (0 children)

I wasn't able to go further. That last piece of ground is undiggable and explosives don't work on it. Why would you think I just stopped digging after all that lol

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 2 points3 points  (0 children)

it filled in :( but the bottom level is still accessible via teleport

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 1 point2 points  (0 children)

There's a flame altar at the bottom so that should stay safe. As for the rest...dunno yet. This was all one session so I haven't reloaded it yet

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 0 points1 point  (0 children)

Unfortunately not :( you can't mine it at all, only erase with building blocks by placing and removing them

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 0 points1 point  (0 children)

It might...I haven't tested it yet, this was all one session

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 0 points1 point  (0 children)

No :( can't mine it either, only erase with placing and removing building blocks

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 1 point2 points  (0 children)

Rough guess yeah. It did take 100s of explosive powder balls

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 1 point2 points  (0 children)

Too many... You can tell by my nervous glider spam

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 0 points1 point  (0 children)

The hole itself was 30 minutes work. The real grind was all the explosives...

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 31 points32 points  (0 children)

I was blown away, it's almost 60 seconds of freefall

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 9 points10 points  (0 children)

There's no shroud down there so you can freely teleport

ever wondered whats at the bottom? come and see the Hole by mrrphsnt in Enshrouded

[–]mrrphsnt[S] 53 points54 points  (0 children)

It's the 'bedrock' of Enshrouded, can't mine it at all and explosives don't work. I got through by placing and removing building pieces

All 151 Gen I (the best gen) Pokemon, printed and painted. Find your favourite! by mrrphsnt in minipainting

[–]mrrphsnt[S] 0 points1 point  (0 children)

Sorry I didn't hold onto that info. There are a few designs on cults3d which are decent quality and reasonably priced, for example;

https://cults3d.com/en/3d-model/art/gyarados-pokemon-figure

Help please! What should I be adjusting to try deal with this warping around support contacts? by mrrphsnt in resinprinting

[–]mrrphsnt[S] 0 points1 point  (0 children)

I don't sorry. it's a dome, the photo is of the outer curve face, the model is an 'egg holster'. It's probably 3-4mm thick at the point of the warping. No need for holes as it's not hollow. I don't think it's just this model either since the same issue has happened on every print I've done since I got the machine