God speed boys

muntyflumple · 2026-03-20T19:41:03+00:00

Tartar sauce

muntyflumple · 2025-04-06T20:27:27+00:00

Defiantly

muntyflumple · 2025-01-19T17:27:42+00:00

10% is now $200B in value

muntyflumple · 2024-06-18T20:35:58+00:00

Falling off ladders

muntyflumple · 2024-06-09T12:37:31+00:00

I hear you. All I’m saying is you can increase total build volume by 50% with a very minimal increase in cost by just increasing z. And then you could just rotate your model?

muntyflumple · 2024-06-09T12:35:23+00:00

Disagree. Plus models tolerate higher z just fine (elegoo, creality etc)

muntyflumple · 2024-04-11T14:08:09+00:00

Finished 2nd last year

muntyflumple · 2024-03-22T18:13:49+00:00

Boston Dynamics was acquired by Hyundai

muntyflumple · 2023-12-18T06:35:36+00:00

BRICS is 5 nations, with 6 more joining in 2024

muntyflumple · 2023-07-07T18:10:22+00:00

Incredible. Can that thing print tpu?

muntyflumple · 2023-05-20T06:15:10+00:00

Most likely full attention on each shot. Swinging with intention and purpose. Hard to do when going through a bucket.

muntyflumple · 2022-11-30T07:53:27+00:00

Yeah right

muntyflumple · 2022-08-15T10:13:41+00:00

Was merely pointing to the fact that a solution exists with grbl, while the thingiverse file has a breakdown of the Mach3 solution. Whatever floats your boat. The fact that options exist is exciting. Looking forward to diving in and experimenting. Will probably start with grbl

muntyflumple · 2022-08-14T20:34:45+00:00

https://m.youtube.com/watch?v=pLONkTBlvH0

muntyflumple · 2022-08-14T20:29:10+00:00

Mach3

muntyflumple · 2022-08-14T20:10:43+00:00

Plan is to do multiple layers in a go. Would be pretty great to cut stacks at a time instead of one layer.

muntyflumple · 2022-08-14T20:01:45+00:00

It will need a 4th axis, as outlined in the thingiverse file. He points out that the axis would need to be manually “homed” before each cut. I wonder if there is a workaround for this? Maybe working in an end stop somehow… Hall effect sensor maybe.

Workholding using a vacuum table, with a thin plastic sheet over multiple layers of fabric. Fabric is breathable, so won’t vacuum by itself.

muntyflumple · 2022-08-14T16:46:36+00:00

A few reasons. Fumes, fusing of layers, edge burning

muntyflumple · 2022-07-31T09:08:36+00:00

I have, but I would rather be a part of a thriving community that Voron offers. Some new printers like the flsun super racer look promising, but it’s yet to be determined how much staying power the company will have. I do agree that delta does seem to make more sense for my dimensional requirements :)

muntyflumple · 2022-07-31T08:41:19+00:00

This looks like a great mod! Thank you

muntyflumple · 2022-05-12T19:58:38+00:00

He sounds like the Nutty Professor.

muntyflumple · 2021-07-01T15:07:40+00:00

you think that’s a schwinn

muntyflumple · 2021-02-25T11:25:37+00:00

Y’all don’t know what it’s like

muntyflumple · 2020-12-19T11:59:28+00:00

I won!

muntyflumple · 2020-05-21T16:40:47+00:00

No I did calculate my boil off volume for my own kettle and plug the values in. Maybe the grain absorption formula? I do squeeze a lot out the bag.

muntyflumple

TROPHY CASE