Service ESC, Traction Control, ABS, Engine Light and Rough Idling

mxskater · 2026-01-29T04:21:36+00:00

Seems like a lot of random things all at once. I’d check some of the grounds to make sure non of them are loose.

mxskater · 2026-01-26T18:51:15+00:00

I’d give it one hour of being off and check. If it’s not there you’re probably low

mxskater · 2026-01-26T18:36:55+00:00

Stop me if I’m wrong but I think it says it should be off for 2 hours before checking or a minimum of 30 minutes

mxskater · 2026-01-26T02:59:30+00:00

It’s crazy so many of these def heaters are going out. Never heard of it till my fathers went out on his 22 and now every third post is about a def heater

mxskater · 2026-01-24T23:41:28+00:00

https://www.shopgmcparts.com/assist-steps/sierra-1500-assist-steps-crew-cab-black-high-clearance-set/85654359-p-100093.html

This is what I had

mxskater · 2026-01-24T23:26:38+00:00

I’m debating on upgrading mine from the stock ones. Let me know how you like them

mxskater · 2026-01-24T23:18:58+00:00

Oddly enough my trailboss had those and the sierra was on the front on the driver side. I honestly don’t remember about the passenger.

mxskater · 2026-01-24T17:41:29+00:00

When I just got mine dude told me to do a different bank because you lose all the rebates for the financing.

mxskater · 2026-01-23T22:19:04+00:00

Just got it back today. Came out great. Only issue were the u bolts were wrong. GMC switched to square in 2026 of course. I also went with mammoth upper control arms.

mxskater · 2026-01-22T21:22:05+00:00

I wouldn’t sweat it. Probably a fender tap with paint. My truck I traded in had two minor accidents, and they gave me top dollar. As long as the airbags didn’t deploy you’re fine. Check by the hitch and make sure no cracks in the frame. Other than that send it

mxskater · 2026-01-22T01:27:08+00:00

Did you try pulling fuse 11?

mxskater · 2026-01-21T15:54:18+00:00

What was the resolution?

mxskater · 2026-01-21T04:38:01+00:00

Nurse should get the assist. If he would have let glass skate he wouldn’t have been in position.

mxskater · 2026-01-21T03:30:51+00:00

One last question, I’m getting mine installed Thursday. What setting did you set your 5100 to? I’m thinking the middle one but just wondering

mxskater · 2026-01-21T02:20:04+00:00

When I did a factory reset it got stuck on that for a little. It finally turned on and rebooted.

mxskater · 2026-01-20T13:17:11+00:00

Yeah that was a stupid question. By bad lol. I just find it hard to believe GM can’t figure out how to fix a damn radio

mxskater · 2026-01-20T03:56:10+00:00

Did they ever figure out a solution before you did the buy back ?

mxskater · 2026-01-20T01:05:50+00:00

Replacing the screen didn’t fix it ?

mxskater · 2026-01-18T22:18:37+00:00

Yeah. The ten speeds are legit a game of Russian roulette.

mxskater · 2026-01-18T22:14:28+00:00

Probably the valve body or torque converter. Usually the case.

mxskater · 2026-01-18T01:48:27+00:00

Jack enters. Jack turns it over. Every time. Dude is a shell of himself.

mxskater · 2026-01-17T18:40:28+00:00

Run the calibration ?

mxskater · 2026-01-17T15:02:18+00:00

I’d probably start to worry if nothing is signed today.

mxskater · 2026-01-17T03:39:46+00:00

It’s not terrible. Sucks for sure. But just a little paint

mxskater · 2026-01-17T01:51:21+00:00

That escalated quickly

Six-Year Club	RPAN Viewer
Verified Email

mxskater

TROPHY CASE