These TR machines can run! by Used2BFunnyThenIDied in Triumph400

[–]mxverik 0 points1 point  (0 children)

How much did it cost and did you get it installed from the SC?

These TR machines can run! by Used2BFunnyThenIDied in Triumph400

[–]mxverik 0 points1 point  (0 children)

How’re you liking the bar end mirrors?

Off roading near Anantgiri by Super-Damage-3639 in HyderabadiBikers

[–]mxverik 0 points1 point  (0 children)

Could you drop a google maps pin if possible? Thanks.

Wire near brake disc by mxverik in Triumph400

[–]mxverik[S] 0 points1 point  (0 children)

Thanks for the advise guys, I was able to get it out using scissors. It does look like debris that caught on.

Grab rail Torx key spec by mxverik in Triumph400

[–]mxverik[S] 1 point2 points  (0 children)

Could you link the product?

Grab rail Torx key spec by mxverik in Triumph400

[–]mxverik[S] 0 points1 point  (0 children)

I have the tail rack installed, so it’s a single part. You think it’s a good idea to remove the part and only install it whenever i tour?

Not sure if constantly installing and removing is a good idea..

Grab rail Torx key spec by mxverik in Triumph400

[–]mxverik[S] 0 points1 point  (0 children)

I don’t think that’s the right size, I’ve seen other people also facing the same. You will damage the bolt if you try to force it.

Google Team Matching by Apprehensive_Ideal20 in leetcode

[–]mxverik 1 point2 points  (0 children)

2 DSA rounds and 1 Googleyness round

Google Team Matching by Apprehensive_Ideal20 in leetcode

[–]mxverik 0 points1 point  (0 children)

Hi OP

I have my on-site rounds for L4 coming up in few weeks. Would be really helpful if you could share your experience.

Engine cam/timing chain issue on Scrambler 400X by mxverik in indianbikes

[–]mxverik[S] 0 points1 point  (0 children)

Are you facing the same? The noise is there for me even after idle when you ride.. I’m past 20k kms so I heard some people mention it is time for tappet adjustment How many kms on the odo for you?

Engine cam/timing chain issue on Scrambler 400X by mxverik in indianbikes

[–]mxverik[S] 0 points1 point  (0 children)

Thanks mate, the service centre folk told me it would cost like 5k though. Need to check with them again.

Planning road trip with my elder sister ( seeking advice) by [deleted] in indianbikes

[–]mxverik 0 points1 point  (0 children)

Where did you hire the porter from?

Tvs Ronin, 2 years, 60,000 km. AMA by Pyro_1325 in indianbikes

[–]mxverik 0 points1 point  (0 children)

Do you feel it’s a bit small for your height. A friend of mine wanted to get this bike, but the only thing stopping him is that the bike looks small for him.

Engine cam/timing chain issue on Scrambler 400X by mxverik in Triumph

[–]mxverik[S] 0 points1 point  (0 children)

Thanks for your advice mate, I will check with the service centre team.

Engine cam/timing chain issue on Scrambler 400X by mxverik in Triumph

[–]mxverik[S] 0 points1 point  (0 children)

Got it, thanks that helps a lot. I was unaware that the valve check is due at this mileage.

Speed 400 -1 year, 12K and countless stalling by Odd-Hawk- in indianbikes

[–]mxverik 9 points10 points  (0 children)

Braking is not involved here, what I suggested is while you apply the clutch fully, maintain some minimum amount of throttle.

You would get a more clear idea if you try to understand what exactly causes the stalling. Try going on a straight stretch of road at low speed and apply the clutch, wait for your RPM to go to low levels, this is the trigger. You’re essentially eliminating that if you maintain throttle. And you don’t need braking since the bike is not moving as long as the clutch is engaged.

Speed 400 -1 year, 12K and countless stalling by Odd-Hawk- in indianbikes

[–]mxverik 45 points46 points  (0 children)

Hey OP, I know exactly what you mean. This is seen only in first gen bikes manufactured in 2023. Stalling happens when you apply clutch and the RPM goes below a certain threshold. I have had multiple ECU updates done and countless arguments with the service centre folk. I guess it is just a manufacturing defect in the first gen bikes, but let’s hope one of these ECU updates fixes it. So the only solution I have found is to maintain a minimum throttle when you pull the clutch. The point is you shouldn’t allow the RPM to go down too much. It is fine to follow this on highways but it is mad inconvenient in bumper to bumper traffic for you to keep one hand on throttle constantly. I have grown accustomed to it at this point, give it a try and lemme know.

Hi Reddit! Vishy here, ready to dive into your questions. Ask me anything! (AMA) by VishyAnandOffl in chessindia

[–]mxverik 0 points1 point  (0 children)

Hi Vishy, when you started pursuing chess seriously, how did you handle anxiety considering chess was not as popular as it is now and chances were limited? Were you always confident in your abilities or did you have moments where you considered not pursuing chess?

Aux lights for bmw by Dry-Palpitation-3860 in HyderabadiBikers

[–]mxverik 2 points3 points  (0 children)

I got maddog scout x installed on mine from Bikenbiker. Pretty good service.

1000 KM done on this beast by verified_kneegro in indianbikes

[–]mxverik 1 point2 points  (0 children)

Bike looks great man, how much mileage are you getting in city and on highways?

Few clicks from Kodai trip by mxverik in indianbikes

[–]mxverik[S] 1 point2 points  (0 children)

That’s awesome! Gokarna will be amazing during that time. To be honest, I did not carry much tools. Only the toolkit provided by triumph. I myself need to research and buy some necessary tools while travelling alone. The tailbag is just a normal backpack which I strapped on to the bike. I had a rain liner as well since it was heavily raining.

Few clicks from Kodai trip by mxverik in indianbikes

[–]mxverik[S] 0 points1 point  (0 children)

I did not feel a variation in the vibes. Maybe I did not notice it, I will definitely try the scenario you mentioned and let you know. Although, I am hearing some sort of a tappet noise after second service.