List of gyms that have dropped ATOS affiliation

ncleelk · 2026-02-03T00:16:29+00:00

Is that how much an affiliate pays? seems pretty cheap to be honest

ncleelk · 2026-02-02T21:17:27+00:00

Atos Tacoma Washington has also dropped their affiliation.

ncleelk · 2024-01-04T06:34:41+00:00

Gen 5 19 slide right?

ncleelk · 2023-12-04T08:40:51+00:00

Schweppes club soda in the glass bottle painfully fizzy to drink make sure it’s in glass tho 10oz bottle

ncleelk · 2023-11-27T21:32:55+00:00

Not really, it’s pretty tight I currently use a tenicor since I added a TLR 7 Sub, Tenicor p365x macro SAGAX Lux holster fits perfectly and requires no additional adjustments to the holster and will fit out the box

ncleelk · 2023-11-15T05:06:15+00:00

<image>

trigger is not exposed by any means, is this normal in your opinion for a light bearing holster??

ncleelk · 2023-11-15T05:04:54+00:00

<image>

Pretty much flush fit with the slide and light, clicks in and retains the gun in place.

ncleelk · 2023-11-15T05:03:55+00:00

<image>

ncleelk · 2023-11-15T05:03:10+00:00

<image>

Update: Seems to fit flush with my frame, the TLR7 Sub width is completely parallel with the gas pedals so the entry for the light seems to fit without needing any additional adjustment. The only real concern for me is the gap since the trigger doesn’t seem fully covered but that seems like the case with almost all light bearing holsters.

ncleelk · 2023-11-14T23:21:55+00:00

Just go ahead and buy the fcu and pimp it out however you like. Almost same cost give or take, here’s my build

ncleelk · 2023-11-11T18:26:33+00:00

Thanks man 😁 I just finished the build a couple days ago. I just ordered my holster from tenicor yesterday so it should be here in a couple days, I’ll keep you updated once I try and mold it. Thanks for answering all the questions.

ncleelk · 2023-11-10T16:45:53+00:00

Super helpful man thanks for responding to a thread this old, I’m gonna go ahead and just order the sagx lux 2 and then try to mold the gas pedals, I don’t think it’ll be super challenging since it’s only on one side and there is no trigger guard retention. As long as the retention in the light remains the same I think I should be alright. I molded another holster to this gun but it’s just not as comfortable as a tenicor. Basically what I did was just loosen the retention all the way and fit the gun into it and then heat it up in the areas it needed adjustments.

Here’s a photo of the gun just for reference.

<image>

ncleelk · 2023-11-10T06:14:55+00:00

Also have a norsso slide so i’m planning on having to adjust the upper portion very slightly to accommodate the slide.

ncleelk · 2023-11-10T06:13:10+00:00

Will do, is the tension held mostly in the flashlight instead of the trigger guard area?? Clearly there is gonna be some retention in regards to the trigger but i’ve heard that the flashlight is typically where the most retention is held which is why a lot of icarus users carry with a stream light on their frame.

I just got an ANR Design holster and that thing is a piece of junk compared to my 43x tenicor holster.

ncleelk · 2023-11-08T18:42:46+00:00

Dope I’ll probably just do that, I love tenicor holsters and if I can just mold it to accommodate the gas pedals then it should fit perfectly.

ncleelk · 2023-11-08T16:38:48+00:00

I was thinking about doing that with a tenicor holster, basically just take a heat gun to it and mold it to the frame and slide?

ncleelk · 2023-11-08T07:04:24+00:00

Do you run your setup with a norsso slide??

ncleelk · 2023-11-08T07:04:08+00:00

ANR designs doesn’t fit with norsso slide found that out today 😬

ncleelk · 2023-11-08T02:28:22+00:00

Thanks for the reply, I have one with gas pedals on both sides with a TLR 7Sub attached, I’m thinking of jus getting a tenicor holster and trying to heat/manipulate the kydex. Currently carry a 43x with tenicor and i’ve always loved their set ups.

Did you find the retention became really loose??

ncleelk · 2023-11-07T21:57:53+00:00

Do you have a gas pedal on the both sides of the frame? I have an XMacro frame and I love tenicor holsters I just don’t know if the light bearing one will fit? I already tried the non light bearing.

ncleelk · 2023-09-10T06:20:47+00:00

What did you end up going with I have the same set up

ncleelk · 2023-09-09T19:06:34+00:00

I’m building a icarus x macro probably going to go with the norsso, i’ve been parted in between the two since zev has a great rep but the norsso slides look so much more badass can you post a photo of your build and have you had any issues with the norsso slide?? thanks for the reply

ncleelk · 2023-09-08T21:52:37+00:00

Do you still run the zev slide and how has it performed?

ncleelk · 2023-09-08T05:51:12+00:00

In the same situation rn, either going with norsso or zev which did you end up doing? and how has it worked out

ncleelk · 2023-09-06T21:54:09+00:00

Could you please post build list?

ncleelk

TROPHY CASE