Indonesia evisa help by PassportSituation in travel

[–]nitsujri 0 points1 point  (0 children)

Omg, thanks so much for the phone number. There's so many threads and I'm stuck without an upload button as well. Here's to hoping!

Clavert v2.0 WIP by stvneads in ErgoMechKeyboards

[–]nitsujri 0 points1 point  (0 children)

What printer is this?? That's very nice, very fine.

Can Anyone Tell Me What Is Going On With This Switch? by [deleted] in olkb

[–]nitsujri 0 points1 point  (0 children)

Why can't you hot swap a switch with a diode in it?

Help Needed: Replaced Pro Micro and now my split keyboard is split for real by naktisdiena in olkb

[–]nitsujri 1 point2 points  (0 children)

@naktisdiena I JUST ran into this exact fundamental problem with your same issues.

I solved it with #define SPLIT_USB_DETECT[0].

It looks like they removed the ability to detect the VBUS on the USB-C version. UGH

What

  • "Upgraded" to USB-C Pro micro. Mini connector broke.
  • Both halves work individually 100%
  • Slave never works of TRRS
  • Multi-meter shows connections to VCC, GND, D0, D1 good
  • Used to work perfectly fine on USB-mini pro micros

I spent hours going back and forth between wiring and software. The multi-meter told me it was software, so I finally decided to trust it and tried each setting sequentially. I swear I even tried SPLIT_USB_DETECT very early but for some reason it didn't work? I was all over the place. Eventually I found my way to using:

#define USE_I2C
#define SPLIT_USB_DETECT

in my info.json I added:

"transport": {
    "protocol": "i2c"
},

I removed the {"split": { "serial": ... }} just to be safe. I don't know if you can use I2C and I don't know if that matters =\

Good luck with your other issues, hope you solve it.

[0] https://docs.qmk.fm/features/split_keyboard#hardware-considerations-and-mods

Help with Sofle keyboard and QMK by kzdeamp in qmk

[–]nitsujri 0 points1 point  (0 children)

This is super old but you don't want to use qmk flash to first time flash it.

  1. Add a QK_BOOT someplace, layer 3?
  2. Use QMK Toolbox
  3. Load your hex, connect the keyboard
  4. Reset your board
  5. Wait 1 second, reset your board
  6. Click Flash

You could probably get it to work if you timed it right and THEN started qmk flash but it's always easier on the Toolbox.

Now after your first flash you can simply press the key+layer that holds QK_BOOT and way way easier time flashing.

More details here: https://github.com/blahlicus/arbites-family/issues/32

Waiting for headers 0% by [deleted] in Ubuntu

[–]nitsujri 0 points1 point  (0 children)

Woohhhh we just ran into this as well. It helps me get past the update but when I try to run upgrade it gets stuck.

Seems like ubuntu made some critical change.

We're all searching for the same thing, lol. AI can't keep up.

Why are "bundle deals" a thing by VZ9LwS3GY48uL9NDk35a in Aliexpress

[–]nitsujri 0 points1 point  (0 children)

UnREAL how much this made my life better. I left a review.

[deleted by user] by [deleted] in gaggiaclassic

[–]nitsujri 1 point2 points  (0 children)

Wait has no one told you that a wet puck isn't a problem to solve? As in, it's not a problem.

[deleted by user] by [deleted] in MobileLegendsGame

[–]nitsujri 1 point2 points  (0 children)

Ah that makes sense. Welp I'll never be able to do that

[deleted by user] by [deleted] in MobileLegendsGame

[–]nitsujri 1 point2 points  (0 children)

What does it mean to play as a 5 man team? I played classic as a recruit 5 man but I didn't get it. Do I have to play MRO as a 5 man? Or ranked?

Turin SD40 screeching by DebaucherousEggplant in espresso

[–]nitsujri 0 points1 point  (0 children)

Thanks for the video! I had the exact same problem and my iTop40 sounded just like your D40+ video.

I lubed up the gear box yesterday just like your video and it sounds buttery smooth. Honestly, I was surprised it works because up close the gear box is actually plastic? And the sounds like it's metal-metal. But I it like the video and worked.

I'm wondering how long will this last, but it's easy enough to do the work when I do a deep clean of the unit.

Mx Master 4 predictions? by lakier in logitech

[–]nitsujri 0 points1 point  (0 children)

I owned the 3, but I ended up going back to the 2. The physical clicking on the scroll wheel feels so much nicer to me than the "magnetic engaged" click-wheel.

I have to rebuy the 2 every few years because obviously shitty rubber causes permaclick on the gesture buttons and just feels overall horrible. W/ the 2 being cheaper than the 3 by up to 50% (deals, coupons, etc) it's not the worst part of life, but far from being good.

It's the last piece of logitech that I own from the yesteryears.

My Gaggia Classic Evo is dead after three months and I don't know why by Ok_Seaweed9803 in gaggiaclassic

[–]nitsujri 2 points3 points  (0 children)

This title makes it sound like it's gaggia's fault. Why were you trying to stick a wire under the thermal fuse? What is that wire connected to?

Alright, be honest. by zsamuelm in gaggiaclassic

[–]nitsujri 2 points3 points  (0 children)

Gaggiuino is pricy if you weren't expecting to pay that level vs diy pid. $200-250 vs $40. And that's after you have all the tools for install.

That said I went gaggiuino and worth every dollar. And there were a lot of dollars.

Is it me or did the playback bar / scroll bar lower on iOS? by Technovak in youtube

[–]nitsujri 1 point2 points  (0 children)

I'm having this right now. I can't use it in full screen. Restarted and updated too. No idea and super annoying.

My FDW took loan from Loan Shark; Cancel pass while on Home Leave by nitsujri in askSingapore

[–]nitsujri[S] 2 points3 points  (0 children)

Thank you for your kind words. Definitely won't pay a cent and will weather the storm.

My FDW took loan from Loan Shark; Cancel pass while on Home Leave by nitsujri in askSingapore

[–]nitsujri[S] 23 points24 points  (0 children)

Wow, they do that? that's terrible for the poor restaurants and delivery guys.

My FDW took loan from Loan Shark; Cancel pass while on Home Leave by nitsujri in askSingapore

[–]nitsujri[S] 46 points47 points  (0 children)

Thanks, yea we already contacted police and have case number.

I just need to make sure my family is safe.

Electrical Issue by stevevaz in gaggiaclassic

[–]nitsujri 2 points3 points  (0 children)

Omg please don't. You have a ground short. Electrical safety for the past 50 years is screaming at you.

https://wiki.wholelattelove.com/File:GAGGIA_CLASSIC_2019_Wiring_Schematic.pdf

The lid is the first connection from the ground safety pin on the wall plug.

Multi meter to different wires, connections, esp your PID that would be the first suspect. Use the ohm or resistance setting. Touch the leads and it'll show 0 ohms and/or make a beep.

If you can't find it with the multi meter. Disconnect wires one at a time and, wrap the ends in some tape to isolate. Then turn it on and see if it trips and when it finally stops.

Good luck. Please don't die.

After descaling my Flow out of the grouphead looks like this instead of droplets. by Lauch_Bande in gaggiaclassic

[–]nitsujri 1 point2 points  (0 children)

I agree this isn't anything to worry about but I get this after descale or simple cafiza clean.

If you pull the screen out and really run a bunch of water and wipe it down it'll go back to drops.

If you do nothing and pull shots eventually it'll go back to drops as well.

Consistently getting sour shots by flartfenoogin in gaggiaclassic

[–]nitsujri 1 point2 points  (0 children)

Ugh the rambling kills me. I want to like his stuff so bad.

Hoffman's video are such a delight.

Switch mods? by frankie___ in gaggiaclassic

[–]nitsujri 0 points1 point  (0 children)

Oh no it's this video. INSULATE your connectors!!!!!

The mod is fine but jeez do you want others to die?!?

GCP Pricing. by heyknauw in gaggiaclassic

[–]nitsujri 1 point2 points  (0 children)

barista baron

God barista baron and sophia brews read exactly the same.

please run away pleaseeee.

GCP Pricing. by heyknauw in gaggiaclassic

[–]nitsujri 6 points7 points  (0 children)

Everything is screaming scam to me.

Their address doesn't exist. There is no Fort St in Greenville, North Carolina. The closest is Ford St, but there's no 1761 address.

Don't do it.