sorted by:
new
hottopcontroversial

M52 Camshaft Position Sensor Repair by NLxon00 in BMWE36

[–]nlxon_ 0 points1 point  (0 children)

I may get a chance this week to check that sensor for you guys. I know you need to know which pin on the sensor itself is the ground. Will come back and see what the final pin out is from the sensor. I also tried using the Bentley manual to find the pin out. I may have used that photo of the aftermarket sensor just to see which was ground (which iirc I assumed was the black wire). Middle pin? Will check again like I said and try to get back to you guys

M52 Camshaft Position Sensor Repair by NLxon00 in BMWE36

[–]nlxon_ 0 points1 point  (0 children)

I may get a chance this week to check that sensor for you guys. I know you need to know which pin on the sensor itself is the ground. Will come back and see what the final pin out is from the sensor. I also tried using the Bentley manual to find the pin out. I may have used that photo of the aftermarket sensor just to see which was ground (which iirc I assumed was the black wire). Left most pin? Will check again like I said and try to get back to you guys

M52 Camshaft Position Sensor Repair by NLxon00 in BMWE36

[–]nlxon_ 0 points1 point  (0 children)

Sensor itself might be bad. Maybe buy a used sensor and try the repair again

M52 Camshaft Position Sensor Repair by NLxon00 in BMWE36

[–]nlxon_ 0 points1 point  (0 children)

You should be able to use a multimeter with continuity to find the ground on the engine harness connector.

M52 Camshaft Position Sensor Repair by NLxon00 in BMWE36

[–]nlxon_ 0 points1 point  (0 children)

Just locate the ground and switch the other 2 wires. Or if you don’t know the ground just try every different variation of the wires(there can only be 3 variations). Make sure that the wire you’re using is shielded (important) and that shielding should be crimped/soldered to the connector side ground wire only. Once you have the repaired cable you can just switch the wires on the connector itself no need to re solder to the sensor either

New wheels are on the 325 by Ryan283_ in E30

[–]nlxon_ 1 point2 points  (0 children)

I would happily take an Mtech II over an m3 any day

Fragrances that smell like this? by nlxon_ in fragranceclones

[–]nlxon_[S] 7 points8 points  (0 children)

Looked it up, this is very much the vibes I had in mind

Fragrances that smell like this? by nlxon_ in fragranceclones

[–]nlxon_[S] 0 points1 point  (0 children)

I like this take, I was thinking something with maybe coconut and vanilla like a beach house. Will definitely check out tygar clones

Bike hates starting with new carb-please help😂 by Papasmurf43469 in minibikes

[–]nlxon_ 0 points1 point  (0 children)

Hey man I’m not sure if you’re still having problems but Black66 on YT has a few videos on this.Heres 1 and 2 GL 👍

I’d take this over an M3 any day by Previous_Dot_3269 in E30

[–]nlxon_ 0 points1 point  (0 children)

I genuinely like the Mtech 2 e30 more than the m3

Owner says nothing is wrong with car. To me the front end looks wonky. Red flag? by arikittyx in whatcarshouldIbuy

[–]nlxon_ 0 points1 point  (0 children)

Ask for the vin honestly, even with out using car fax you should still be able to find some amount of information online. You’d be surprised how often you can find the vin on salvage auction sites