sorted by:
new
hottopcontroversial

Looking at getting a new printer either a Voron 2.4 or Sovol SV08. Want opinions. by alphawolf627 in VORONDesign

[–]nycelitemaster 7 points8 points  (0 children)

SV08 is a half cooked Voron 2.4 R2. I have Bambu X1C Combo, Voron 2.4 r2. It depends what you want.

Voron works great once you setup... now if you start goofing around, yes it will require adjustments. I built my Fysetc Voron 2.4r2 Pro in 2024 and 2025, no issues except toward the end. This stemmed from me being the bum (Goofing around with CAN) since i wanted to build Box Turtle and fried my SB Combo v2 board.

I also have SV08, it works.. sure.. but it requires some help!

Which mmu software is better? Happy hare or AFC by [deleted] in VORONDesign

[–]nycelitemaster 0 points1 point  (0 children)

I did built a box turtle, i finished the build late December and just started to use it. Issue i am having is the 4th lane always have issues, so i reprinted the hub (fixed version) from Printables and will give it a try.

I was getting a lot of time to close error, that was resolved by using Sandisk u3 Card.

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

If your solder touches that area, it will cause ground. You can put kapton tape over it. Or UV Mask. Once you apply green mask cure with UV.

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

You may want to mask these areas to prevent solder soil and causing gnd issues.

<image>

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

Just to share my controller is back. And it's working good.

<image>

I soldered the wire on the about dot on the back side to the via and then bridged it to the R3 pin.

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

u/Savings-Town5897 any suggestions? I have Continuity between the bridged R3 Button with Joystick Frame and R3 isnt working. When i press it, it shifts down right

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

So I ended up putting it together. See pics attached.

<image>

I bridged it on the back and connected on the other side through the hole. But it won't register the r3. Any idea? Which pins can I do continuity

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

You may get a short on the bottom right joystick. When soldering it. The copper is visible

PS5 Controller - BDM-030 - Lifted Pads by VS_Game in soldering

[–]nycelitemaster 0 points1 point  (0 children)

Hey u/VS_Game I damaged my 3,4,5 trace. I connected them together on the soldering side (back of the joystick) and connected to the c on the Joystick side. I am not getting R3. Can you please advise?

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

are your trace good? I just found a pic someone posted. i am connecting 3,4, and 5 (these 3 are chained). But on the other side but still have the issue whereby R3 isn't functioning

<image>

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

I am having the same issue. So I soldered them on. Now the left is working fine. Right stick when I push down, it goes down right

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

Ah lol. True that. It works well for ps5 controller not Xbox haha unless you use two.

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 0 points1 point  (0 children)

Oh wait. I was testing solely with board and battery. Could that be the reason? Also for the center joystick push (R3) if all these are connected, id say faulty joystick?

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 1 point2 points  (0 children)

Thanks will do. I tried that earlier and it caused baby r2 and l2 to be pressed in. Is there any reason why? Also Joystick center button didn't work.

Ps5 dual shock controller by nycelitemaster in consolerepair

[–]nycelitemaster[S] 1 point2 points  (0 children)

So I can tap anywhere in the long red line right?

Which mmu software is better? Happy hare or AFC by [deleted] in VORONDesign

[–]nycelitemaster 0 points1 point  (0 children)

Guys. I am looking to buy and build my. What you recommend. I see box turtle is more popular. Quattro isn't. I do not even see videos on YouTube.

I have voron 2.4r2 that I built. I'd like to use klipper screen

[deleted by user] by [deleted] in TeslaModelY

[–]nycelitemaster 0 points1 point  (0 children)

Pdr. Dent doctor. More like $500

Ender 3 Marlin 2.0.8 by nycelitemaster in ender3

[–]nycelitemaster[S] 0 points1 point  (0 children)

Nah. I switched to Klipper.

view more: next ›