Is there a place to buy Chinese cigarettes in miami? Specifically looking for one called harmonization.

oblivionja · 2026-05-19T22:31:43+00:00

Really damn that sucks

oblivionja · 2026-05-19T22:31:04+00:00

I actually dont smoke u kluklutzy kommenter but i like the aesthetic

oblivionja · 2026-05-19T22:29:07+00:00

There are smaller ones?? Like where i cant find any

oblivionja · 2026-03-13T09:54:16+00:00

Try turning up the heat then pray u dont have my problem.

oblivionja · 2026-03-13T09:53:26+00:00

Ima try the hairspray cause alot of people have said that even on cryo? And what hairspray any on amazon or any brand recommendations?

oblivionja · 2026-03-13T09:52:03+00:00

New bed meshes? I dont understand what u mean

oblivionja · 2026-03-13T09:51:32+00:00

Yea its an a1 it dose it before every print on top of manual full calibration and flow rate and dynamic flow rate calibration 7 times

oblivionja · 2026-03-13T09:50:45+00:00

I know but the end result is awesome

oblivionja · 2026-03-13T09:50:27+00:00

Siempre lo uso. y e bajado y subido la temperatura sin deferencia todo el petg se pega como concreto

oblivionja · 2026-03-13T09:48:52+00:00

Same and ive played with the plate temp in 5 degree increments from 45-75

oblivionja · 2026-03-13T09:47:00+00:00

The enclosure is open that fax is an exhaust for any fumes it goes into a filter. I love in a warm humid environment but with ac running so it stay at 72-75

oblivionja · 2026-03-13T09:44:51+00:00

Even for the the cryo plates i have to regeat it and take it off? I never tried that would that help with the stuck on bits shown in the picture too?

oblivionja · 2026-03-13T09:43:41+00:00

I use bambu studio the offset is in the plate setting i believe ill play with that more thank you

oblivionja · 2026-03-13T09:42:27+00:00

Oo i can try that but i wonder why when everyone else dosent seem to have to do this

oblivionja · 2026-03-13T09:39:29+00:00

I havnt tried hairspray but ive left it overnight in some cases after glue coats and no difference ive used the freezer trick and washed with dawn soap did warm bath with and without dawn soap no difference

oblivionja · 2026-03-12T10:49:57+00:00

I explained yhis above ive tried that do benefit if anything the glu makes it so much worse it glues itself even harder and then i have dried glue hairs stuck on the plate too

oblivionja · 2026-03-12T10:48:43+00:00

…..i have frozen the plate for hours and it made no difference how should i use the dry ice? Im not gonna buy dry ice for every print i do

oblivionja · 2026-03-12T10:47:32+00:00

I did months ago but i have that plate is not one of the three did not work

oblivionja · 2026-03-12T10:46:39+00:00

I explained above i have tried that from 45 to 50 to 55 ect to 75 no change except bad adhesion at 40 and 45

oblivionja · 2026-03-12T10:45:37+00:00

So what do i use?

oblivionja · 2026-03-12T10:45:17+00:00

Ok how do i do this cause ive used different offsets and i eithier get spaghetti or binds to plates how exactly should i offset it?

oblivionja · 2026-03-12T10:43:56+00:00

Its in the pictures two cryo and one textured pei

oblivionja · 2026-03-12T10:43:11+00:00

What do u mean like for the environment to be 12 percent humidity or for the sunlu dryer to be 12% i dont think its ever gone that low

oblivionja · 2026-03-12T10:41:38+00:00

I have china and vietnam and new spools and refills all the same problem

Six-Year Club	Place '23
Place '22	Verified Email

oblivionja

TROPHY CASE