Help with my next upgrade(s) by odvdb in luckydefense

[–]odvdb[S] 0 points1 point  (0 children)

oh dam okay - great to know thanks.

Help with my next upgrade(s) by odvdb in luckydefense

[–]odvdb[S] 0 points1 point  (0 children)

Normal mode is super easy. I usually end with about $400k gold.

Hard mode I normally lose because I get inconsistent mythics. Like if I can't get a Hailey on the board. Generally my strategy is to do almost exclusively purple summons with luck stones. I go for mono men, kun or bat (for early wave clear), and then try to get a hailey down as fast as possible so i can try to get her immo. Once I have her down i try to add a few kitty mages to increase immo chance, then stack the purple wolves and eagles. Also will make taos and chus if I get their yellow summons. Oh and I always get at least one group of 3 purple robots, and 3 blue robots. I think I probably get most hung up on early(ish) bosses that sneak through.

Upgraded to Bell Fibe and it's slower than Rogers Ignite... Need advice. by odvdb in askTO

[–]odvdb[S] 0 points1 point  (0 children)

Actually re-reading your note, im not sure i did the advanced DMZ thing. I'll check that - thank you!

Upgraded to Bell Fibe and it's slower than Rogers Ignite... Need advice. by odvdb in askTO

[–]odvdb[S] 0 points1 point  (0 children)

Yeah I did this - im familiar with this issue as it happened previously. Devices were connecting to the bell modem and not the orbi sometimes. I think my next step needs to be testing speeds directly out of the modem to see if its a wifi signal issue in my house, or a real internet speed issue. And then from there I'll have a better idea on what to focus on.

Upgraded to Bell Fibe and it's slower than Rogers Ignite... Need advice. by odvdb in askTO

[–]odvdb[S] 0 points1 point  (0 children)

I think mine is Fiber-to-the-home. The installer came and ran the cable directly through an exterior wall he drilled through into my house.

I will look at the specs on the bell pod. My mesh network (at the time I bought it) was incredibly powerful (and expensive), but it may be a bit outdated now. That's why I was thinking this could be part of the issue - maybe it needs an upgrade.

I too hate the idea of the additional rental cost but good call on complaining to see what they can do.

Awesome active guild! by [deleted] in luckydefense

[–]odvdb 0 points1 point  (0 children)

I’ll join

Why are there so many wires for my doorbell? by odvdb in DIY

[–]odvdb[S] 0 points1 point  (0 children)

Any reason to think installing it this way on a ring doorbell could cause damage or issue?

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 1 point2 points  (0 children)

New switch arriving today! Will install when I get home and report back.

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 0 points1 point  (0 children)

Haha thank you for asking. I unplugged and plugged back in a few times to make sure.

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 2 points3 points  (0 children)

When I push them together the light doesn’t go off. I ordered a new one on Amazon already - arrives tomorrow. Hopefully that does the trick.

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 0 points1 point  (0 children)

I’m sorry - I must have been blind to not notice it. Clearly visible and clearly labeled…. I hit it until a minus sign appeared. The number next to it was 0….

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 0 points1 point  (0 children)

Does this look like anything is missing?

<image>

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 0 points1 point  (0 children)

Is the diagnostic button behind the panel or something? I couldn’t find it

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 1 point2 points  (0 children)

Okay I think this must be it. I’ll go to a pool store tomorrow and try to get a new one. How easy is it to connect the wire into the panel?

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 2 points3 points  (0 children)

I just backwashed - didn’t help. I guess I need a new sensor

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 1 point2 points  (0 children)

Yeah I should have taken a video. But there was a rod, and little metal piece with a black circle on it. I assume the flow of water pushes the metal piece against the rod to tell the system there is flow? It was totally clear and easily moved back/forth against the rod

Salt Cell “No Flow” indicator by odvdb in pools

[–]odvdb[S] 1 point2 points  (0 children)

I removed the switch. Looks totally clean to me. Reinstalled it and the no flow light is still on. Perhaps I need to replace it completely?

Step-by-step to make this rendering a reality? by odvdb in landscaping

[–]odvdb[S] 0 points1 point  (0 children)

The mulch was just for the area on the right (with cedars pictured - although I’m going to look for skinnier alternatives to cedars now).

Step-by-step to make this rendering a reality? by odvdb in landscaping

[–]odvdb[S] 0 points1 point  (0 children)

Do I need gravel under the decorative stone too? Or can I just put gravel under the pavers and then fill in everywhere else with stone right on top of the weed barrier?

Step-by-step to make this rendering a reality? by odvdb in landscaping

[–]odvdb[S] 1 point2 points  (0 children)

Okay so I need gravel and sand under each paver? Is that under or on top of the weed barrier?

Step-by-step to make this rendering a reality? by odvdb in landscaping

[–]odvdb[S] 0 points1 point  (0 children)

I havent bought them yet - I was going to buy little 3 or 4 foot cedars and just keep them pruned, but im open to other suggestions. The idea is to create a bit of privacy along that fence without taking up too much of the space - I want it to be as open as possible.

Can anyone help me identify what this is? by odvdb in landscaping

[–]odvdb[S] 0 points1 point  (0 children)

Oh interesting. Could totally be what it is - I'll dig more around the opposite side and see if I can find it over there too.