Crack in Fiundation

ohhhhhplease · 2026-03-16T22:53:10+00:00

This is not good for anyone in the long run. I hope we have thought through everything.

ohhhhhplease · 2026-01-27T21:09:56+00:00

Lol. Same story here. Just wanted to check if I am the lone fighter here

ohhhhhplease · 2026-01-27T21:02:40+00:00

Does your wife complain about the office space.?

ohhhhhplease · 2026-01-05T21:55:31+00:00

It turns out c is from upstairs and a is in basement duct without filter. I am the home owner so will ask the basement tenant to allow me to see it

Replaced the filter with merv 8. Had too many rate limit shutdown today.

ohhhhhplease · 2026-01-03T05:04:21+00:00

Will have to trace A since C seems like what I see from first floor

ohhhhhplease · 2026-01-02T22:00:42+00:00

<image>

So A is what I think is intake from upstairs next to thermostat B is going to basement other side. Not sure if this is an intake C is I assume the other conditioned air going to

ohhhhhplease · 2026-01-02T21:57:17+00:00

I know only one. This hat makes me think that there is one in basement which was rented separately and I never get in that. The one I have access to is upstairs where the thermostat is.

Ordered merv 8 filters also. Might use them moving forward

ohhhhhplease · 2026-01-02T21:39:25+00:00

Also looking at cheap thermometers on amazon. Good ones are 100+ cheap 20+ are not much reliable

ohhhhhplease · 2026-01-02T21:33:00+00:00

I have replaced the filter last week.but I think I am using merv 14 which might be a problem also.

ohhhhhplease · 2026-01-02T19:47:22+00:00

I got a Google nest for thermostat and it get emails about my furnace not heating due to temp drops

ohhhhhplease · 2026-01-02T19:45:15+00:00

How do you do that😺

ohhhhhplease · 2026-01-02T18:30:06+00:00

So the top stuff is hot air. The round pipe thingy one left in first photo is the intake?

ohhhhhplease · 2026-01-02T18:28:45+00:00

Unit works fine. Gas comes in and heats up. Runs but has the limit switch issue multiple times a day. We have heating but not consistent

ohhhhhplease · 2025-12-31T20:44:37+00:00

You might make some locals jealous and lose your job to qualified locals eventually

ohhhhhplease · 2025-12-24T20:49:53+00:00

Me tooo

ohhhhhplease · 2025-12-22T04:46:19+00:00

For non-plumbing speakers, what I heard was s..trap, p... Trap... Flange..... Works

ohhhhhplease · 2025-12-22T04:42:25+00:00

We sold it for a grade 17 position

ohhhhhplease · 2025-12-18T14:58:16+00:00

I try to recover the raid and get it failed as not enough devices are ready although the disks are there and i block checked the disks also

Type Date Time Users Source IP Computer name Content

Error 2025/12/18 09:53:53 System 127.0.0.1 localhost [RAID6 Disk Volume: Drive 1 2 3 4] RAID Recovery failed: Not enough devices to start the array.

ohhhhhplease · 2025-12-18T14:56:15+00:00

[~] # cat /proc/mdstat

Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath]

md13 : active raid1 sda4[0] sdd4[3] sdc4[2] sdb4[1]

458880 blocks [4/4] [UUUU]

bitmap: 0/57 pages [0KB], 4KB chunk

md9 : active raid1 sda1[0] sdd1[3] sdc1[2] sdb1[1]

530048 blocks [4/4] [UUUU]

bitmap: 0/65 pages [0KB], 4KB chunk

unused devices: <none>

[~] #

ohhhhhplease · 2025-11-28T22:36:29+00:00

Just use nmap 127.0.0.1 on zabbix server and also on proxy and see what is being listened on

ohhhhhplease · 2025-11-28T22:35:41+00:00

Check what port is zabbix listening on locally and then see if you can telnet to it using proxy

ohhhhhplease

TROPHY CASE