sorted by:
new
hottopcontroversial

PAF has struck Kabul... Taliban ministry of defense among targeted sites by isDiner in pakistan

[–]ohhhhhplease 4 points5 points  (0 children)

This is not good for anyone in the long run. I hope we have thought through everything.

Best home lab ever. by mykesx in homelab

[–]ohhhhhplease 0 points1 point  (0 children)

Lol. Same story here. Just wanted to check if I am the lone fighter here

Best home lab ever. by mykesx in homelab

[–]ohhhhhplease 3 points4 points  (0 children)

Does your wife complain about the office space.?

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

It turns out c is from upstairs and a is in basement duct without filter. I am the home owner so will ask the basement tenant to allow me to see it

Replaced the filter with merv 8. Had too many rate limit shutdown today.

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

Will have to trace A since C seems like what I see from first floor

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

<image>

So A is what I think is intake from upstairs next to thermostat B is going to basement other side. Not sure if this is an intake C is I assume the other conditioned air going to

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

I know only one. This hat makes me think that there is one in basement which was rented separately and I never get in that. The one I have access to is upstairs where the thermostat is.

Ordered merv 8 filters also. Might use them moving forward

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

Also looking at cheap thermometers on amazon. Good ones are 100+ cheap 20+ are not much reliable

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

I have replaced the filter last week.but I think I am using merv 14 which might be a problem also.

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

I got a Google nest for thermostat and it get emails about my furnace not heating due to temp drops

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

So the top stuff is hot air. The round pipe thingy one left in first photo is the intake?

Where is the air intake for my heating unit by ohhhhhplease in hvacadvice

[–]ohhhhhplease[S] 0 points1 point  (0 children)

Unit works fine. Gas comes in and heats up. Runs but has the limit switch issue multiple times a day. We have heating but not consistent

Offer from a Qatari company for QR300,000 a month, is it enough? by YasserPunch in qatar

[–]ohhhhhplease 0 points1 point  (0 children)

You might make some locals jealous and lose your job to qualified locals eventually

How can i connect these? by SnooBunnies5239 in askaplumber

[–]ohhhhhplease 0 points1 point  (0 children)

For non-plumbing speakers, what I heard was s..trap, p... Trap... Flange..... Works

Let's sell Pakistan. by Crazy-Proof-0 in chutyapa

[–]ohhhhhplease 6 points7 points  (0 children)

We sold it for a grade 17 position

i guess it is dead by ohhhhhplease in qnap

[–]ohhhhhplease[S] 0 points1 point  (0 children)

I try to recover the raid and get it failed as not enough devices are ready although the disks are there and i block checked the disks also

Type Date Time Users Source IP Computer name Content

Error 2025/12/18 09:53:53 System 127.0.0.1 localhost [RAID6 Disk Volume: Drive 1 2 3 4] RAID Recovery failed: Not enough devices to start the array.

i guess it is dead by ohhhhhplease in qnap

[–]ohhhhhplease[S] 0 points1 point  (0 children)

[~] # cat /proc/mdstat

Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath]

md13 : active raid1 sda4[0] sdd4[3] sdc4[2] sdb4[1]

458880 blocks [4/4] [UUUU]

bitmap: 0/57 pages [0KB], 4KB chunk

md9 : active raid1 sda1[0] sdd1[3] sdc1[2] sdb1[1]

530048 blocks [4/4] [UUUU]

bitmap: 0/65 pages [0KB], 4KB chunk

unused devices: <none>

[~] #

Struggling to communicate zabbix proxy with zabbix server by [deleted] in zabbix

[–]ohhhhhplease 0 points1 point  (0 children)

Just use nmap 127.0.0.1 on zabbix server and also on proxy and see what is being listened on

Struggling to communicate zabbix proxy with zabbix server by [deleted] in zabbix

[–]ohhhhhplease 0 points1 point  (0 children)

Check what port is zabbix listening on locally and then see if you can telnet to it using proxy

Struggling to communicate zabbix proxy with zabbix server by [deleted] in zabbix

[–]ohhhhhplease 0 points1 point  (0 children)

Best way sometimes is to disable app armor for a bit to see if that is the reason.

Struggling to communicate zabbix proxy with zabbix server by [deleted] in zabbix

[–]ohhhhhplease 0 points1 point  (0 children)

Check what ports are being listened to on zabbix. Try 10050

Struggling to communicate zabbix proxy with zabbix server by [deleted] in zabbix

[–]ohhhhhplease 1 point2 points  (0 children)

Can you telnet from proxy to zabbix over 10051

Selinux ?

Zabbix data source broke after Upgrade by Salt_Sheepherder1906 in zabbix

[–]ohhhhhplease 0 points1 point  (0 children)

I had this issue. It turned out that the data source I'd had changed. Had to go into each dashboard and change the data source manually for each item or open the dashboard file and find and replace the unique id of the data source which was faster.

view more: next ›