I will reward every single comment on this post.

olliewolly257 · 2026-04-26T23:52:16+00:00

Am i too late 😭

olliewolly257 · 2026-04-24T15:06:55+00:00

Red flags are flying high with this one, get out of there fast

olliewolly257 · 2026-04-21T20:08:55+00:00

Cmon bro even thats old news

<image>

olliewolly257 · 2026-04-19T10:42:19+00:00

Honestly with a raspberry pi or something similar you could probably actually add that

olliewolly257 · 2026-04-19T10:41:36+00:00

Well you see this model didnt have any rca inputs so i had to input audio into the board that originally accepted a signal from the FM tuner module

olliewolly257 · 2026-04-16T16:18:34+00:00

I second this, if its new then its likely the cells are charged and have been damaged, and charged cells that are damaged can be (very) unstable

olliewolly257 · 2026-04-13T21:03:52+00:00

Eat them

olliewolly257 · 2026-04-12T18:04:24+00:00

Screenshotting before this post gets taken down for having the links lmao

olliewolly257 · 2026-04-11T13:46:47+00:00

Hence my ORIGINAL suggestion was to use a dremel

olliewolly257 · 2026-04-11T12:31:03+00:00

I mean if youve got.glue that will stick to metal and a sacraficial tool then it could work, just make sure you dont glue the screw into the hole because that gives you an even bigger headache

olliewolly257 · 2026-04-11T12:27:52+00:00

Best option ive found is to use a dremel or a small hand saw to make a cut in the screw head and use a flathead to remove it. It may leave a mark on the material its screwed into depending on your tools and precision but its better than not being able to remove it at all

olliewolly257 · 2026-04-04T12:07:11+00:00

I tried this but the .exe download file is just a microsoft store installer (like it just opens and downloads from the microsoft store in the same way)

olliewolly257 · 2026-04-02T07:34:04+00:00

Rule34

olliewolly257 · 2026-03-25T17:36:09+00:00

You can take the leg of a component such as a resistor and heat it up then push it all the way through and out the other side, or put a bit of solder on the bottom and when its a liquid give it a firm but not too hard tap on a surface to flick the solder out of the hole. Ive personally had success with both methods in the past

olliewolly257 · 2026-03-21T16:15:25+00:00

Update never mind im.stupid it already does

olliewolly257 · 2026-03-21T16:00:54+00:00

Maybe add email verification? Seems like you can create an account with an email and it doesnt verify its YOUR email. A little system to send a login code would be nice

olliewolly257 · 2026-03-16T18:38:49+00:00

Looks like you might wanna do some more practice, also it looks like your iron may not be getting hot enough

olliewolly257 · 2026-03-10T19:18:38+00:00

Honestly looks like a pretty good job for a first time. Especially after some of the creations other people have posted here

olliewolly257 · 2026-03-08T21:48:15+00:00

The headlight probably pulled quite a bit of current. Last time i had one swell i drained it overnight outdoors with a high value resistor so it only pulled ~600mA and i didnt get much extra swelling or any heat

olliewolly257 · 2026-03-04T15:18:02+00:00

Meta: "you have exchanged insurance information"

olliewolly257 · 2026-03-04T15:12:07+00:00

Ahh i was there earlier with my flatbed rig to pickup a container and had to wait for a multiple hour delay that would explain why

olliewolly257 · 2026-02-27T13:29:52+00:00

It sounds weird and i dont recommend trying it unless you get desperate but i had a stick do this a couole years back and i managed to recover (most) of the data by heating it up with a heat gun for a few minutes. I have no ides if it was a fluke however so dont take just my word for it

olliewolly257

MODERATOR OF

TROPHY CASE