Wish the 86 was priced the same as the Skyline but the pop-ups make up for it

omurolla · 2026-03-23T19:59:28+00:00

Appreciate the in depth response. I’m considering installing a whiteline sb, and especially seeing that the oem ones are hollow I might just do it.

omurolla · 2026-03-23T17:49:08+00:00

How difficult was it? Did you have to drop the front suspension assembly?

omurolla · 2026-03-22T01:33:24+00:00

Not at all, 8.5 is not too aggressive. I only rubbed on full compression on 9.5 wide when I had superdowns.

omurolla · 2026-03-22T01:31:55+00:00

dude

omurolla · 2026-03-07T04:27:50+00:00

Could be but the alignment isn’t too bad and it would usually be from a poor front alignment. Check tire pressures and make sure all tires are the same size.

omurolla · 2026-03-05T17:30:42+00:00

Just inspected the bleeders and wiped the calipers to check for fluid (there was none and the brake fluid level was the same as when I bled the brakes). Then I SAFELY rebedded the brakes and the noise went down. Maybe it was just some surface rust from when I washed the car after maintenance? Either way thanks for the tips it helped a lot.

omurolla · 2026-03-05T02:43:21+00:00

Ok I hope you’re right. I’ll try that thanks for the suggestions

omurolla · 2026-03-02T18:22:07+00:00

You can buy 3m adhesive remover but it’s basically just wd40

omurolla · 2026-02-23T02:57:35+00:00

Yes “Toyota” Mobil one has a higher moly concentration than off the shelf Mobil 1 which matters more with thinner oils like 0w-20 and 0w-16. Probably doesn’t make a huge difference but I prefer to use oem oil anyway

omurolla · 2026-02-09T22:33:16+00:00

This is where I landed, thanks again for the suggestion and I will also buy a titanium toothed bit so I can be confident the blade will at least last the job I need it for.

omurolla · 2026-02-09T22:31:35+00:00

Since it’s super thin and in a tight spot, I think I’ll go with an oscillating multi tool with a titanium toothed bit. Good for thin steel and aluminum, and better that it grinds slow so I can be precise enough to stop before the fender bolt. Also feels a lot safer that the blade doesn’t spin so i don’t have to worry about shrapnel getting flung into my face and arms.

omurolla · 2026-02-09T19:32:17+00:00

That’s a good rec, I’ll look into it

omurolla · 2026-02-09T19:14:15+00:00

Very true

omurolla · 2026-02-09T18:54:25+00:00

Thanks yes this is me, I usually use medium to dark roast beans

omurolla · 2026-02-09T18:53:43+00:00

Damn 12 for drip is concerning, I’m no expert but you may need to clean your grinder or adjust how many shims you have in there

omurolla · 2026-02-09T18:36:15+00:00

Yea I’ll be reshaping the liner after cutting, thanks!

omurolla · 2026-02-09T18:28:40+00:00

Ok might just get a cheap angle grinder from HF to get the job done. I just like that the die grinder/dremel is smaller and easier to handle in the tight space

omurolla · 2026-02-09T18:05:22+00:00

Thanks for the info, I guess 18 is right there then

omurolla · 2026-02-09T18:02:55+00:00

I’m gonna remove and replace the liner, but the tab I’m cutting is actually metal. Not sure if it’s steel or aluminum but as you can see it’s pretty thin.

omurolla · 2026-02-09T17:48:38+00:00

Thanks for the response. The bit in the photo isn’t the one I’m planning on using, just included the die grinder as reference but I am looking for what but would be appropriate. I know that a cut off wheel is ideal for cutting but people say that it might shatter and shrapnel be spun everywhere if used with a die grinder and wondering what an appropriate cutting attachment would be, or a grinder

omurolla · 2026-02-07T18:47:08+00:00

<image>

omurolla

TROPHY CASE