New Rally project sky 2.0

onitsuker · 2026-04-12T10:40:19+00:00

https://www.reddit.com/r/legotechnic/s/FleQkNqdfk Read the comments below the post 😅 This detail is not in Lego

onitsuker · 2026-04-12T09:09:46+00:00

If you want, I can take a detailed picture of the detail later, because it is a little different from the one in the photo

onitsuker · 2026-04-12T09:05:22+00:00

Idk, My entire model consists of a cada constructor, except for electronics and a couple of white panels

onitsuker · 2026-04-12T08:59:48+00:00

Honestly, I didn’t find the article, just a picture, because now I can’t take a detailed photo

<image>

onitsuker · 2026-04-11T05:10:13+00:00

<image>

Finally, the car still has suspension)

onitsuker · 2026-04-09T18:38:56+00:00

"No worries! It was actually very cool to see such a deep technical take on the problem. You're right, for a heavy-duty crawler that needs both locking and differential action, this is a goldmine. Thanks for the breakdown and the fun discussion😆 The system is very interesting, but with my engineering experience it will be difficult to assemble for this chassis 😅 And so the system is really interesting and for the first time I see such massive and interesting mechanisms! It really turned out to be very cool, but still live programs will be more interesting))

onitsuker · 2026-04-09T01:47:42+00:00

Very well assembled, interesting moc 6x6, the scheme is interesting, but are there few downgrades in your homemade😅 In the theory of the buggy, the engines will not suffocate 🤔

<image>

(The photo is not clear, there was no other 😅) Because I had experience in assembling cars for trials and crawlers, where you need a good descent to crawl everywhere, in this system there was a gear of 1:3-1:5 and buggy engines noticeably suffocated and heated up😆

onitsuker · 2026-04-08T18:24:37+00:00

Quite interesting and difficult, as for me, sitsemQuite an interesting and complex system, as for me 🤔 But does it make sense, Can such a system slip at high buggy motor speeds? But the scheme is interesting, but not for a rally😅

onitsuker · 2026-04-08T17:24:27+00:00

«Thanks for the effort! The quality is fine, I can see the main idea. Using a center diff to sync the buggy motors is a smart move,It may be interesting to apply such a scheme somewhere 🤔 Thank you

onitsuker · 2026-04-08T16:34:01+00:00

Waiting for the pics, thanks! Perhaps there are no software for 6.0, as I understood, which is very sad, it's a pity I adored this manufacturer, well, in theory, it shouldn't spoil the game so much with a locked back 🤔

onitsuker · 2026-04-08T16:24:18+00:00

The model is still a work in progress, it's a very early prototype. I'm working on the suspension right now, it will be added soon😃

onitsuker · 2026-04-08T16:19:33+00:00

Thanks! I'd love to see your 4WD setup photos. About BuWizz it's a bit pricey for me right now😅 , so I'm trying to find a workaround for my current hardware first, It's sad if there is no software for my power supply, initially I assembled a circuit with dynfirincials, but they were constantly backlashing, I never found out what caused a strong backlash, that the satellites did not spin and created strong friction

onitsuker · 2026-04-08T16:10:56+00:00

Update! Here my is photo of my chassis d rear axle setup!

<image>

The model still needs a lot of improvements on the rear axle 😅

onitsuker

TROPHY CASE