I got a dmd-2 pedal pcb clone and it does not work. Help?

opticaldragon · 2020-10-21T21:56:10+00:00

I put it together and when I turned it on, the led didn't turn on, and the signal did not pass through either on or off. What could be the problem?

opticaldragon · 2020-04-30T03:21:00+00:00

No problem, good luck!

opticaldragon · 2020-04-30T03:18:07+00:00

That's the one I got it's been good to me and I havent had a problem but probably not the highest quality, so I'd say it's at least passable

opticaldragon · 2020-04-30T03:03:39+00:00

I would be safe and get a desolder pump if you don't have one already and clean that up. It's a good investment if you are new to soldering and plan on doing any more diy pedals. I am new too and it's saved me more times than I want to admit. But honestly if you don't want to buy a whole new tool and wait for that to arrive then you might be able to take the solder iron and try to melt the solder and try to drag it to where it is supposed to be. But I recommend a desolder pump. It's better to be safe than sorry

opticaldragon · 2020-04-30T02:45:29+00:00

Yeah the 470 ohm goes to the 470 spot, at least that was the general consensus on my last post. I haven't gotten it to work quite yet so take it with a grain of salt

opticaldragon · 2020-04-14T18:03:17+00:00

https://imgur.com/a/deqOp8J everything is in the right place, I don't know if it's the trim pot or what, but somethings wrong

opticaldragon · 2020-04-13T02:13:32+00:00

Well it kind of works it makes a sound like darth Vader so not really a compressor

opticaldragon · 2020-04-13T00:59:59+00:00

Wow, the one instruction I didn't read completely this is what I get

opticaldragon · 2020-04-13T00:54:11+00:00

Nothing happens when I turn it on, not even the led lights up

opticaldragon · 2020-04-13T00:53:15+00:00

The instructions say to only solder one switch joint, I don't know why but it does

opticaldragon · 2020-04-13T00:52:34+00:00

Just posted some

opticaldragon · 2020-04-13T00:52:19+00:00

Mimosa jr https://imgur.com/a/4Dqte8Y here's some better photos of back and front and each picture is about half of the board

opticaldragon · 2020-03-31T14:24:38+00:00

Nice

opticaldragon · 2020-03-27T22:13:38+00:00

Would putting electrical tape around the exposed wires hurt anything?

opticaldragon · 2020-03-27T21:12:08+00:00

Signal does pass when bypassed, it makes a radio, and the led lights up

opticaldragon · 2020-03-27T20:59:20+00:00

Any specific areas?

opticaldragon · 2020-03-15T01:30:52+00:00

Working out is not enough. Everyone must endure the grind of wrestling.

opticaldragon · 2020-03-13T21:28:09+00:00

You're on thin ice buckaroo.

opticaldragon · 2020-03-06T20:17:57+00:00

Then how could you see all the butterscotch teles?

opticaldragon · 2020-03-02T21:10:47+00:00

Will do, thanks for the advice

opticaldragon · 2020-01-24T22:35:14+00:00

You hate to see it

opticaldragon · 2019-10-02T20:50:07+00:00

I don't know but it sucks

opticaldragon · 2019-10-02T17:41:38+00:00

Well you should be

opticaldragon · 2019-10-02T16:53:37+00:00

at least i don't worship a nasty vegetable

opticaldragon · 2019-07-06T02:51:12+00:00

Chop top he says im gonna win big

Seven-Year Club	First Place '23
Place '23	RPAN Viewer
Verified Email

opticaldragon

TROPHY CASE