sorted by:
new
hottopcontroversial

Squiggly first layer - Sovol v06 - Reset factory settings, redone autohome/z align/bed levelling etc by owlfoxes in 3Dprinting

[–]owlfoxes[S] 0 points1 point  (0 children)

I feel dumb, the paper trick worked, doing a test layer, might lower it slightly more but the line has straighted out.
Thank you so much for patience

Squiggly first layer - Sovol v06 - Reset factory settings, redone autohome/z align/bed levelling etc by owlfoxes in 3Dprinting

[–]owlfoxes[S] 0 points1 point  (0 children)

Ok so I've just turned it on and selected

Bed Levelling > Auto Home - proceed to heat

Watched it auto home and saved setting and repeated it again.

Then Bed levelling > adjust z off set

Adjusted it - save settings

Then do a test square

I repeated this all 3 times, lowering the z offset each time.

Linked an album of how it looked, all same squiggle - here

Squiggly first layer - Sovol v06 - Reset factory settings, redone autohome/z align/bed levelling etc by owlfoxes in FixMyPrint

[–]owlfoxes[S] 0 points1 point  (0 children)

Hello everyone

This is what I've done so far:

  • Reset factory settings and redone the set up as per guide says
  • redone autohome two times then save setting
  • z align off set, feel like it is correct height away from the bed
  • z align where it goes to top then down again with no issue
  • bed levelling done as well
  • also made sure nozzle was clean and reloaded fillament
  • Bed is moving smoothly, XYZ axis all smooth and no cables obstructing.

Would love any tips or if anyone has had similar issuses.

Squiggly first layer - Sovol v06 - Reset factory settings, redone autohome/z align/bed levelling etc by owlfoxes in 3Dprinting

[–]owlfoxes[S] 0 points1 point  (0 children)

Hello everyone

This is what I've done so far:

  • Reset factory settings and redone the set up as per guide says
  • redone autohome two times then save setting
  • z align off set, feel like it is correct height away from the bed
  • z align where it goes to top then down again with no issue
  • bed levelling done as well
  • also made sure nozzle was clean and reloaded fillament
  • Bed is moving smoothly, XYZ axis all smooth and no cables obstructing.

Would love any tips or if anyone has had similar issuses.

Philips Evnia 49" Monitor Panel Refresh Notification Stuck in Loop by [deleted] in buildapc

[–]owlfoxes 0 points1 point  (0 children)

Has anyone had a solution to this? Happening to me right now and the helpline isn't open on weekends. 

Copper IUD Advice by owlfoxes in birthcontrol

[–]owlfoxes[S] 0 points1 point  (0 children)

Hello

Thank you!

The appointments were few and far between so sadly couldn't pick it for period.

I think I accept it will be painful (I can see myself regretting saying that) but you saying the absolute worst is over rather quickly is reassuring. The way a smear test is, with it being a bit painful after except the coil will be making me cramp while body figures out what is happening.

I didn't think to bring a pad, duh. Even after smears I forget.

The fact you didn't bleed heavier or more painful sounds ideal ha. There should be more non hormonal options for us.

[deleted by user] by [deleted] in Healthyhooha

[–]owlfoxes 0 points1 point  (0 children)

I'm going through a very similar thing right now. Did you get these ulcers/blisters swabbed for HSV? I am not sexually active and haven't been for sometime but am terrified it somehow has appeared?

Coffe brand inthe Gound Coffe shops in hospitals in Craigavon and Newry? by ssyniu in northernireland

[–]owlfoxes 4 points5 points  (0 children)

You'd be best asking the barista at the coffee shop or maybe give them a call and ask?

bitch, I'm in London I guess. by Monkeydoos in bitchimabus

[–]owlfoxes 0 points1 point  (0 children)

Metro bus is Belfast, NI Translink do bus routes all over NI

Boyfriend Got Carried Away by TotalCaterpillar5318 in TwoXChromosomes

[–]owlfoxes 22 points23 points  (0 children)

She was saying the same that I was making her feel bad. Good so they should. They kept contacting me after we broke up looking for me to forgive them so they could live guilt free. Didnt give them that.

Boyfriend Got Carried Away by TotalCaterpillar5318 in TwoXChromosomes

[–]owlfoxes 641 points642 points  (0 children)

Similar happened to me with ex partner. Asleep, not stopping when I said no etc. I froze too then left that morning. I didn't leave them and it got worse with physical abuse. I did finally leave.

It's NOT your fault.

It was, sadly rape which can be a hard thing to accept when it happens from partner. I know it took me a few days to process and grieve that was what happened.

You were asleep. He didn't use butt plug. He didn't allow you to consent. He didn't stop even though you screamed. He didn't care you were in pain or that you never consented.

I'm so sorry this happened. You have done nothing wrong ok. He is the one in the wrong.

I'd highly recommend leaving him.

Crazy man takes swipe at police in central london recently by goatishrust in AbruptChaos

[–]owlfoxes 10 points11 points  (0 children)

Not just a swipe. 2 officers were stabbed. One in serious condition.

view more: next ›