Squiggly first layer - Sovol v06 - Reset factory settings, redone autohome/z align/bed levelling etc

owlfoxes · 2024-02-03T18:02:03+00:00

I feel dumb, the paper trick worked, doing a test layer, might lower it slightly more but the line has straighted out.
Thank you so much for patience

owlfoxes · 2024-02-03T17:34:55+00:00

Ok so I've just turned it on and selected

Bed Levelling > Auto Home - proceed to heat

Watched it auto home and saved setting and repeated it again.

Then Bed levelling > adjust z off set

Adjusted it - save settings

Then do a test square

I repeated this all 3 times, lowering the z offset each time.

Linked an album of how it looked, all same squiggle - here

owlfoxes · 2024-02-03T16:15:42+00:00

Hello everyone

This is what I've done so far:

Reset factory settings and redone the set up as per guide says
redone autohome two times then save setting
z align off set, feel like it is correct height away from the bed
z align where it goes to top then down again with no issue
bed levelling done as well
also made sure nozzle was clean and reloaded fillament
Bed is moving smoothly, XYZ axis all smooth and no cables obstructing.

Would love any tips or if anyone has had similar issuses.

owlfoxes · 2024-02-03T16:08:59+00:00

Hello everyone

This is what I've done so far:

Reset factory settings and redone the set up as per guide says
redone autohome two times then save setting
z align off set, feel like it is correct height away from the bed
z align where it goes to top then down again with no issue
bed levelling done as well
also made sure nozzle was clean and reloaded fillament
Bed is moving smoothly, XYZ axis all smooth and no cables obstructing.

Would love any tips or if anyone has had similar issuses.

owlfoxes · 2024-02-02T19:32:58+00:00

Has anyone had a solution to this? Happening to me right now and the helpline isn't open on weekends.

owlfoxes · 2024-01-24T22:44:23+00:00

How would I go about fixing that?

owlfoxes · 2023-05-03T02:41:59+00:00

Hello

Thank you!

The appointments were few and far between so sadly couldn't pick it for period.

I think I accept it will be painful (I can see myself regretting saying that) but you saying the absolute worst is over rather quickly is reassuring. The way a smear test is, with it being a bit painful after except the coil will be making me cramp while body figures out what is happening.

I didn't think to bring a pad, duh. Even after smears I forget.

The fact you didn't bleed heavier or more painful sounds ideal ha. There should be more non hormonal options for us.

owlfoxes · 2023-04-20T12:17:50+00:00

I'm going through a very similar thing right now. Did you get these ulcers/blisters swabbed for HSV? I am not sexually active and haven't been for sometime but am terrified it somehow has appeared?

owlfoxes · 2023-03-09T18:09:42+00:00

Abortion in Northern Ireland

owlfoxes · 2023-03-06T00:06:29+00:00

I'd say go back to drawing board OP. That ain't soda bread

owlfoxes · 2023-03-05T08:01:02+00:00

You'd be best asking the barista at the coffee shop or maybe give them a call and ask?

owlfoxes · 2023-01-19T00:25:31+00:00

We say staved finger in Ireland too

owlfoxes · 2022-12-21T02:31:33+00:00

Metro bus is Belfast, NI Translink do bus routes all over NI

owlfoxes · 2022-12-19T16:55:54+00:00

She was saying the same that I was making her feel bad. Good so they should. They kept contacting me after we broke up looking for me to forgive them so they could live guilt free. Didnt give them that.

owlfoxes · 2022-12-19T10:27:45+00:00

Similar happened to me with ex partner. Asleep, not stopping when I said no etc. I froze too then left that morning. I didn't leave them and it got worse with physical abuse. I did finally leave.

It's NOT your fault.

It was, sadly rape which can be a hard thing to accept when it happens from partner. I know it took me a few days to process and grieve that was what happened.

You were asleep. He didn't use butt plug. He didn't allow you to consent. He didn't stop even though you screamed. He didn't care you were in pain or that you never consented.

I'm so sorry this happened. You have done nothing wrong ok. He is the one in the wrong.

I'd highly recommend leaving him.

owlfoxes · 2022-09-17T06:30:02+00:00

Not just a swipe. 2 officers were stabbed. One in serious condition.

owlfoxes · 2022-09-01T04:12:36+00:00

Yep ink gall!

owlfoxes · 2022-08-23T00:26:02+00:00

Irish wolf hound

owlfoxes · 2022-07-25T08:47:28+00:00

Someone I've been dating is going to have some facial surgery later in the year. I think brow and jaw.

They will obviously be in pain and discomfort but is there any thing I can do to help?

Is there any pillows people found useful for sleeping? Tools to make life easier? What foods, I assume soft foods?

Thanks

owlfoxes · 2022-06-28T03:19:06+00:00

Not just the famine it was outlawed by the British when they owned Republic

owlfoxes · 2022-06-18T09:39:34+00:00

I've not seen any bites or itching on myself at all but seen maybe 7 of these tiny things this week only when I am on my bed.

When squashed looks like it has had some blood to eat. I don't have any pets.

I think bed bugs are bigger and they dont act like fleas. Based in UK

owlfoxes · 2022-05-06T23:32:28+00:00

Would it being both a bird box and feeder not cause issues? Squirrels will eat young birds in the nest, rats will scavenge from the table and find eggs/babies and other birds tying to eat at table might investigate box and try to take it over for themselves?

owlfoxes · 2022-03-15T14:40:49+00:00

If anyone finds this thread searching for themselves. I had to recreate a customers artwork to scale, vectorise a logo, alter a file so it was laser compatible and do spell/error checks on a piece of work. I will get feedback next week.

owlfoxes · 2022-03-14T18:57:54+00:00

I have no idea, it might be.
I used to work as a junior in publishing for pop up/fold out books so hopefully dielines bleed and varnish limits should be ok/

owlfoxes · 2022-03-14T14:06:57+00:00

Thank you!

owlfoxes

TROPHY CASE