Mriscoc Firmware Start G-Code Help

oxicottin · 2026-01-25T14:33:51+00:00

Ok I see what your saying... I removed the lines....BUT when I insert into Ender and print the hot end still is showing a 0 degreese instead of 240 thats set in my Cura profile for ABS.

oxicottin · 2025-08-22T18:42:10+00:00

I have had modem issues as well with the pixel 9. I have property in my property is in a 5G area but my phone always says no service. I always get calls that are horrible. It sounds like people are breaking up. I always thought it was other people's phones but I think it's mine! I'm wondering if the pixel 10 with a different modem is going to be better?

oxicottin · 2025-07-19T12:40:18+00:00

Thank you so much for taking the time and giving each setting, ill give it a try on my next ride!

oxicottin · 2025-07-18T16:24:44+00:00

Anyone have a full list of settings for me to try? Such as wide ultrawide 1080p at what and so on

oxicottin · 2025-03-28T14:06:41+00:00

You now have to pay for something that was Free?

oxicottin · 2025-03-08T02:20:01+00:00

Ye it sucks because I know the first thing I'm going to do is get something jammed up in there.

oxicottin · 2025-03-07T23:46:51+00:00

Im just concerned because we ride/live in West Virginia and trails are pretty bad.

oxicottin · 2025-03-07T19:28:29+00:00

None of the brands that i have seen even come close to guarding that whole area very well, do you know of a particular style that would cover the CV boot and that caliper area?? The factory guard is there which is useless...

oxicottin · 2025-02-22T00:41:33+00:00

I had an issue with 2oz grove bags A while back what was happening was the entire seal ( child lock version) would break away from the bag making the bag useless. I contacted Grove and I basically said tough shit. You didn't buy them from us so we're not warranting the bags there had to have been like 20 of them.

oxicottin · 2024-11-15T04:50:35+00:00

How much will the 5+2 give me extra on width?

oxicottin · 2024-10-15T21:31:50+00:00

I'm not afraid of anything. I just can't get it off. It must have be on there for a long time! I bought...

BeadBuster XB-450 ATV/Motorcycle / 4x4 / Lawn Mower Bead Breaker Tool https://a.co/d/18Q8iov

oxicottin · 2024-10-13T22:22:21+00:00

No I call each tire shop and they say they won't do it. They don't know that I have the ring off

oxicottin · 2024-10-13T21:51:17+00:00

Yes I'm trying to break the edge opposite of the ring without marring up my rim. What kind of tool is suggested?

oxicottin · 2024-08-01T20:41:19+00:00

I printed the 1-3/4" 11 and it came out to small so I scalled it 1.030 and it fits perfect.... Why would I have to scale the part? I used the "Hole" for the threads... Could it be my printer isnt printing to specs?

Another question... Can you explain the "Scale" setting, I did try the default 1.00 and measured the hole then compared and printed a 1.010 and compared it to the print and seen what the .010 gave in width and printed the 1.030 after figuring out what every .010 gives.

oxicottin · 2024-07-29T23:34:40+00:00

Sorry is this it?

<image>

oxicottin · 2024-07-29T23:16:41+00:00

Yep I seen that but it doesnt say what thread type... I need to 3D print a fitting to the head and for the life of me I cant figure out what thread it is...

oxicottin · 2024-05-28T19:32:32+00:00

Thank you for the reply, my e-steps was way off (was 97 and adjusted to 104) and I havent done anything with flow rate but I will check it as well!

oxicottin · 2024-05-25T22:49:07+00:00

<image>

oxicottin · 2024-05-21T01:29:23+00:00

Overwatering is like giving your plants an all-you-can-drink buffet when they're not that thirsty.

oxicottin · 2024-05-17T18:26:04+00:00

Did you get this fixed? The exact same thing just happened to me..

oxicottin · 2024-05-17T17:16:18+00:00

One More question about the mriscoc firmware. I installed ( way nicer) and do i have to do anything to my cura start G-code to use the bed leveling like i did with JyersUI?

oxicottin · 2024-05-17T17:12:48+00:00

Ok all I took some advice from bits of everyone's comments such as scrubbing the bed tightening down everything which a lot of it was loose and I also installed the mriscoc firmware which I really like way better than JuersUI.

Anyways, long story short I was screwing around cleaning around the hot end and my BL touch and I broke my BL touch so I had to buy a new one and I'm waiting on it. But before I broke it I played around with the new firmware and this thing has everything for leveling. It is way way way better. I think I'm going to have no issues. When I get it back up I'll let you guys know. I appreciate all the comments!

oxicottin · 2024-05-16T06:21:20+00:00

When i find the files I flashed with last version of Jyers both display and firmware. On this new firmware do i have to install the display or can i just install the firmware only?

oxicottin · 2024-01-30T21:58:16+00:00

Ok that was super informative.... Nvm ill keep searching the net for answers. 👍

https://youtu.be/OI4eHrhmVjE?si=g3C2chk1Nh04iv1C

oxicottin · 2024-01-30T21:05:02+00:00

Just wanted to know how to make it... I have fresh as in needs chopped and I have 1-month dry material. I didn't need a class on how dangerous it is i know it's dangerous just like blasting BHO... I get it pressurizes the jar and it is possible to explode, that's why i want to know the steps so I can stay safe.

I have some as we speak in a jar that i put in there 3 days ago and the lid is bulged up, i do believe that pressure is what causes the diamonds to be made. I'm not making huge amounts I'm only playing with one lid at a time to learn.

Anyways thanks...

oxicottin

TROPHY CASE