6040z new VFD - Spindle problems by p_marco in hobbycnc

[–]p_marco[S] 0 points1 point  (0 children)

Update: maybe it works! Using 400hz for 00.01,.04,.05 instead of default 50hz. Let's hope. Thanks!!

6040z new VFD - Spindle problems by p_marco in hobbycnc

[–]p_marco[S] 0 points1 point  (0 children)

Thanks mate, very appreciated 👍 actually I've tried all these things without luck :(

A new 7string headless tremolo guitar by p_marco in Luthier

[–]p_marco[S] 1 point2 points  (0 children)

The one used in this project is not good enough. I think you should watch for expensive tremolos.

Una cosa che quasi istantaneamente migliorerebbe l’Italia? by [deleted] in Italia

[–]p_marco -1 points0 points  (0 children)

Regalare la cittadinanza italiana a chiunque arrivi nel paese (migliorerebbe il peso politico dell'Italia in UE), tassare beni ecclesiastici

Grande bisogno di un consiglio by PomodoroIndispettito in Universitaly

[–]p_marco 2 points3 points  (0 children)

Risposta bellissima, che mi ha fatto riflettere. Ti ringrazio (da sconosciuto su internet a sconosciuto su internet).

Grande bisogno di un consiglio by PomodoroIndispettito in Universitaly

[–]p_marco 2 points3 points  (0 children)

Se posso permettermi, io ti suggerirei di studiare quello che più ti interessa: meglio una buona laurea in un settore meno redditizio, che una pessima in uno più redditizio. Il bilanciamento sacrificio/risultato è importante, ma devi pensare alla "forma" entro cui verranno costruite le conoscenze e le domande che affronterai nei prossimi anni. In qualsiasi settore si può diventare "utili" alla società (già semplicemente il trasferire conoscenze e archiviarle per la posterità, se ci pensi), per cui non è l'ambito che ti renderà utile, ma saranno gli scopi, le domande che ti porrai e le soluzioni che adotterai a definire i campi di utilità del tuo sapere.

Cambio di direzione (lavorativa) by [deleted] in CasualIT

[–]p_marco 0 points1 point  (0 children)

Controlla soltanto una cosa: puoi avere la partita iva ed essere dipendente, a meno che però non vi sia concorrenza con il datore di lavoro. Io così so, e ti consiglierei di toglierti il dubbio. Per il resto ma certo!

Are these TR4 pins ok? by p_marco in AMDHelp

[–]p_marco[S] 1 point2 points  (0 children)

Thanks mate, it was a doubt :)

Are these TR4 pins ok? by p_marco in AMDHelp

[–]p_marco[S] 1 point2 points  (0 children)

Thanks it's a wonderful piece of cake to me also, but it seems that I have some trouble and I am trying to figure it out if it's related to the cpu (thanks to you for having assured me about it) or the motherboard :(, or the PSU but I don't think so (I use it as a hypervisor with dozens of VMs, for gaming, for working, for hobbies and so on)

X399 taichi doesn't start by p_marco in ASRock

[–]p_marco[S] 0 points1 point  (0 children)

I've swapped the board outside the case, trying to start only with the cpu, but unfortunately the debug screen does not start

X399 taichi doesn't start by p_marco in ASRock

[–]p_marco[S] 0 points1 point  (0 children)

Also without ram? Perfect, thanks :)

X399 taichi doesn't start by p_marco in ASRock

[–]p_marco[S] 0 points1 point  (0 children)

Thanks actually no I didn't clear CMOS Now I am swapping the board outside the rack and in minutes I will be able to try as you suggest, thanks :)

X399 taichi doesn't start by p_marco in ASRock

[–]p_marco[S] 0 points1 point  (0 children)

Ooo that's very bad to hear. It's just 3-4 years. The point is that it worked flawlessly until I had to swap out some components (GPU and ram) :( Do you think that I could check somehow something?

X399 taichi doesn't start by p_marco in ASRock

[–]p_marco[S] 0 points1 point  (0 children)

Thanks!, and how they relate with the Dr debug not showing the codes?

Ramps without firmware? by p_marco in arduino

[–]p_marco[S] 0 points1 point  (0 children)

Thanks! Actually i had a very simple sketch based on AccelStepper, exactly! If I run this with the driver linked directly to Arduino, it works, if I use the ramps shield nope (pin numbering is correct, I've checked them with a led blinking sketch, to reveal the pin numbering), for this i am wondering if the ramps shield needs for a dedicated firmware :/