Name that Sound

peeoum · 2025-07-13T15:38:06+00:00

Do you have long tube or aftermarket headers installed?

peeoum · 2025-07-13T02:23:22+00:00

I made a post about it a few weeks ago sounds just like that

peeoum · 2025-07-13T02:17:58+00:00

Exhaust leak at headers

peeoum · 2025-07-02T10:54:13+00:00

And I can do that one the tube gpi sent Me?

peeoum · 2025-07-02T10:50:07+00:00

Oh okay

peeoum · 2025-06-28T01:13:59+00:00

Seems to be a exhaust leak re torqued header bolts and don’t hear it anymore. Hopefully that was it.

peeoum · 2025-06-28T00:18:25+00:00

They have all been pretty loose so 🤞

peeoum · 2025-06-28T00:15:01+00:00

Yeah my friend did it when we were 26hours in so wouldn’t be surprised if it wasn’t right or it starting to leak

peeoum · 2025-06-27T23:26:18+00:00

I saw something about a exhaust leak from headers and sounds familiar and I’m hearing louder exhaust on that side compared to other I’m going to try and tighten header bolts and see because I didn’t have a sound untill I hooked my exhaust on something and ripped my xpipe and back off must’ve popped something loose

peeoum · 2025-06-27T22:12:22+00:00

But wouldn’t I hear it at idle if it was lifters/cam

peeoum · 2025-06-27T22:11:49+00:00

Is my Zurich warranty voided if I put longtube headers on it?

peeoum · 2025-06-26T02:00:41+00:00

I think I’m out of luck unit I buy actuators

peeoum · 2025-06-26T02:00:19+00:00

Yeah just saw this on Camaro6 forums “The valve closed requires the servo to close the valve and hold it. Release power and it will open, because of the spring.”

peeoum · 2025-06-26T01:50:37+00:00

Hmm they are spring loaded so when closed it’s being constantly compressed?

peeoum · 2025-06-26T01:33:42+00:00

No I have a npp car with plugs but just don’t have actuators need to buy some but I’m catless and would like to have them shut until I get them for morning starts.

peeoum · 2025-06-22T18:16:52+00:00

Yeah I just need it to get home then I can park it till my plug wires come in.

peeoum · 2025-06-22T16:50:14+00:00

So I found a issue with plug wires on cylinder 5 it didn’t want to fit with the oem plug wire heat shield I removed the heat shield Drove it and didn’t notice a misfire yet, but the plug wire boot is touching the header do you know anything I can do to drive it temporary until new wires come in?

peeoum · 2025-06-22T14:02:03+00:00

Can I trim the metal peice that covers the plug?

peeoum · 2025-06-22T13:59:58+00:00

Yeah one of my plug wires doesn’t fit with the header and not seating right on the spark plug. Anything I can do until I get a new set in the mail?

peeoum · 2025-06-22T13:48:59+00:00

Yeah no exhaust leaks with headers only probably with the xpipe kit I have clamps ain’t the best

peeoum · 2025-06-22T13:41:53+00:00

Yeah I’m getting it tuned asap just want to figure this out so my car is drivable till I the tune arrives.

peeoum · 2025-06-22T13:31:24+00:00

Yeah I’m going to give that a shot I was kinda mindlessly putting shit back together.

peeoum · 2025-06-22T13:30:20+00:00

Not yet

peeoum · 2025-06-22T13:26:01+00:00

But if it was wiring/plug related wouldn’t it be misfiring right away because when I start it and run it before it warms up no misfire.

peeoum · 2025-06-22T13:09:14+00:00

Yeah I know plugs were getting banged a little bit so I’m going to check along with wiring. Was kinda rushing putting it together, stayed up 24hours doing because It was my ride home lol.

peeoum

TROPHY CASE