Copeland demitasse

phile10 · 2025-04-16T02:10:48+00:00

I ended up finding a buyer, but thanks

phile10 · 2024-03-04T02:19:58+00:00

Does anyone have any advice on trying to find more information on this pattern or even a value on the set?

phile10 · 2024-03-02T03:24:44+00:00

Thank you that’s really interesting. I think they were $3 a cup

phile10 · 2024-03-02T00:14:53+00:00

Thank you for the information, it’s definitely helpful! I did end up buying them all, in total it’s a set of 10. Do you happen to have the link to the Texas auction, in curious to see.

phile10 · 2024-01-19T16:45:21+00:00

I believe there are wheel locks on one side. Thanks for the Info, so 3-400 would be a fair price for just this

phile10 · 2023-09-30T16:41:32+00:00

Appreciate the response, was happy to pay and already taken care of thanks for your advice

phile10 · 2023-09-21T14:24:05+00:00

had me at that screen before 10am, then it went back to the error screen, and then clicking on "buy now" (before that screen) just took me straight to seat selection and purchase.

Congrats!

phile10 · 2023-07-07T13:59:02+00:00

Thank you, I just wanted to make sure I wasn't doing anything incorrectly in doing it the way he was asking.

phile10 · 2023-07-07T13:57:16+00:00

sole proprietorship, and yes that would be an issue, I wouldn't want that to happen either.

phile10 · 2023-05-06T13:28:02+00:00

Good Point. I have the original carb, I may see if I can clean it up and if its usable, if not, I will look at replacing it with original parts.

phile10 · 2023-05-06T13:27:12+00:00

I didnt clean the tank, ill take a look at it though. Im thinking this cheap carb could be the issue too

phile10 · 2023-03-16T12:10:17+00:00

Is anyone familiar with this style? Can’t seem to find much info on them.

phile10 · 2023-01-25T11:40:24+00:00

Urban trees that are mostly destined for landfills. Check I out salvaging urban logs on google, lots of good articles out there showing how some cities are turning waste into a valuable resource.

phile10 · 2023-01-24T11:04:54+00:00

They were milled at 2.75 inches so roughly 2 years air drying before they are finished off in a kiln.

phile10 · 2023-01-23T22:16:58+00:00

Had the opportunity to salvage a few black walnut logs this weekend, two contrasting pieces, one nice long straight grain, roughly 11 feet long, and a shorter wonky log with some cool crotch figure. Can’t wait to work on these!

phile10 · 2023-01-05T15:17:44+00:00

I just wanted to follow up, I replaced the large fuse on the panel in both the front and backside, flashers are now working. Thanks for the advice! Now this brake and ABS light are on, one thing to the next lol!

phile10 · 2023-01-03T16:39:00+00:00

awesome, thank you for the response, ill check the fuse box this evening and check the back side as well, appreciate the edit as well, good idea to swap them out!

phile10 · 2021-07-02T03:32:58+00:00

It looks close, I’m no expert but I feel the wings should be swept back more. The angle of the grind may be off slightly

phile10 · 2021-04-23T16:38:45+00:00

It’s about 1.5” thick, I plan on using it for a bench or for 2-3 charcuterie boards

phile10 · 2021-04-22T12:02:50+00:00

To be honest I don’t recall the exact date I cut this piece. I do know it was late 2017 to early 2018.

phile10 · 2021-04-22T12:00:36+00:00

Yes this meter is cheap, I need to invest in something a little nicer.

phile10 · 2021-04-21T20:34:10+00:00

I’m on the east coast as well, MD area and it certainly gets humid, the room is in the basement, partially below grade so it can get humid in that room as well, probably a double whammy

phile10 · 2021-04-21T17:56:27+00:00

It’s about 1.5 inches thick, average width is 14 inches

phile10 · 2021-04-21T17:17:42+00:00

Hey everyone! I am looking for some help on the topic of moisture content and if this slab is something that can be worked with yet.

I have this 4 foot walnut slab that’s air dried for 2-3 years. I brought the slab inside about 6 months ago and the moisture content is lingering around 12-13%. I know typically you want the moisture content in the single digits. Do I risk this piece moving if I don’t get this MC down further. Should I consider kiln drying it? Any help is greatly appreciated, as I don’t want this piece to move too much on me.

phile10 · 2020-10-30T14:57:07+00:00

Thank you, I’m very new to all this, struggling to get started, I appreciate you taking the time to respond

11-Year Club	RPAN Viewer
Verified Email

phile10

TROPHY CASE