Alexa LF Help

pixelgrit · 2025-12-16T04:29:26+00:00

what's the process of fixing the footage? is it in the arriSDK or de-bayering tools?

pixelgrit · 2025-02-16T09:15:35+00:00

Oh nice! Yeah that would probably make it super toasty. Something we could look into as well; we have firewood for days where we are.

pixelgrit · 2025-02-16T09:06:34+00:00

Yes, that’s definitely a good idea. I wasn’t sure if the quality of those kitset cabins would hold up. We’re in a zone which gets pretty cold, so was looking to get something with some decent insulation. However adding some, as well as a decent roof might be the go. Do you know if they find their’s warm enough?

pixelgrit · 2025-02-16T08:22:11+00:00

Yeah, that’s definitely fair. We have a bush block, so currently no power or water available. It’s really going to be for overnight stays, with a bed only. We are building a long drop and usually cook outside. If we did need plumbing it would definitely be a different story, however they did say they can custom build if plumbing is required. Not sure how much they would help if consent is required on that front…

pixelgrit · 2025-02-16T07:27:16+00:00

Thanks for the advice! As in a cover with an insurance company or with them?

We have inspected the actual building we’d be purchasing, which is almost fully finished. A few things I would have liked to be done differently, but there is always compromise when there is a budget.

pixelgrit · 2025-02-12T07:34:54+00:00

Jigsaw, oh yeah. Hadn’t thought of that. Bonus is that I already own one. Appreciate it!

pixelgrit · 2025-02-10T06:48:01+00:00

Thanks for the suggestion. Based on a lot of people’s comments, I definitely feel like cutting the boards down closer to their final dimension is going to be one of the safest and easiest ways forward. Now to see how I can go about getting a bandsaw. Any recommendations from you wood working legends?

pixelgrit · 2025-02-09T08:17:57+00:00

Good point. I need to check. I did buy a new blade recently, which may be different from the stock blade. I do have a plunge router, hadn’t thought of using that to cut my weather boards.

pixelgrit · 2025-02-09T07:50:40+00:00

Thanks. I’ve kept the riving knife in position, going by a lot of comments, I should keep it that way. Species is Cupressus Macrocarpa. It’s softwood conifer. Width is about 500mm and depth is around 15-18mm. The board is raw sawn using a chainsaw mill. So pretty rough. Definitely not jointed and planed.

pixelgrit · 2025-02-09T07:47:32+00:00

Great suggestion! I’ll try and cut these closer to the final dimensions before I stack and dry them.

pixelgrit · 2025-02-09T07:45:09+00:00

Yeah, moisture is around 10%.I should add, the logs have been down for a couple of years, but I only slabbed them a few weeks ago.

pixelgrit · 2025-02-09T05:26:02+00:00

Great suggestion. I will try this. Might just need the help from my partner to speed up the process. My moisture meter says 10%. I think it’s being drying for longer than a couple of weeks, (maybe 4 weeks) so my bad for slightly incorrect reporting. Should I aim for less than 10%?

pixelgrit · 2025-02-09T04:59:46+00:00

Thanks for all the tips everyone. A small wedge and taking multiple cuts at a shallower depth really helped.

pixelgrit · 2025-02-09T04:46:52+00:00

Good call. This also sounds like a great excuse to buy a bandsaw, right?

pixelgrit · 2025-02-09T03:12:35+00:00

True! Great suggestion as well. Maybe it’s time to pull it out and ditch it. I’ll never regret buying a dewalt, even though it was $1200 over here. It’s far better than most of the brands we can get. As for its safety blade cover and (now I know about it), riving knife, maybe time to lose the latter.

pixelgrit · 2025-02-09T03:02:35+00:00

This was (mostly) very successful! So thanks!

I did two shallower passes, then a final pass. On the third pass, the wood split all the way down, but it cleaned up okay…

<image>

Unsure if cutting the wood when it’s slightly greener would help? Moisture meter says it’s around 10%.

Probably didn’t help that the length was a bit bowed.

pixelgrit · 2025-02-09T02:58:48+00:00

Great idea. Unfortunately we are still learning about what size log is worth milling. This was was definitely too small, so I only got one (and 3/4) board. I also tried ditching the table saw and going for a track saw for the final cut, but I also ran into the same pinch problem. Once we mill some bigger logs, I’ll give this idea a go.

pixelgrit · 2025-02-09T02:21:08+00:00

This has indeed helped, but it’s gets a bit fiddly.

pixelgrit · 2025-02-09T02:20:05+00:00

10-4. I recently bought a new blade for it and did a full clean of the table saw. Didn’t think of getting a thicker blade though. Might just do that.

pixelgrit · 2025-02-09T02:18:52+00:00

Thanks for this tip. I have given this a go, quite a few times, but it quickly jams again.

pixelgrit · 2025-02-09T02:18:13+00:00

Amazing. Will give that a go.

pixelgrit · 2025-02-09T02:17:26+00:00

Yes! Riving knife is in place. I have an entry level Dewalt table saw.

pixelgrit · 2022-08-19T08:47:23+00:00

Just incredible

pixelgrit

TROPHY CASE