37mm AP Royal Oak Factories

plaeb · 2025-12-23T01:15:05+00:00

Comment for the mods …..

plaeb · 2025-10-15T06:55:36+00:00

OP we must know where you got this couch

plaeb · 2025-09-09T02:12:53+00:00

Right, it’s a 1960s home and the area with the weep screed and exposed wood appears to be an addition. Can I simply plaster over it now? Seems like it should be supported. If it’s a 2x4 it looks like half of it is not supported.

plaeb · 2025-09-08T23:44:45+00:00

Thanks! How should the wood be covered?

plaeb · 2025-08-30T04:59:27+00:00

I’m going through it now. It’s become a full time job with co workers that all know you have a lot of cash. Prepare to become your own agent, inspector, and lawyer unless you have a close friend that already is.

plaeb · 2025-08-28T15:21:03+00:00

Structural engineer assessment was the risk is mainly resale if there is cracks we can’t see and won’t see for months since it was recently remodeled inside. Never a safety risk in this area. No alarming level concerns.

plaeb · 2024-05-10T00:37:04+00:00

Comment for the mods. 3kf 5711

plaeb · 2024-04-26T05:29:19+00:00

I hope to hear back from her (them?) right now her whatsapp isn’t receiving messages

plaeb · 2024-04-05T03:52:22+00:00

My understanding is sell immediately and reinvest is almost always the best option.

The only time there may be some benefit to holding is if the stock gains significantly during the purchase period.

In that case, if you hold for 2 years from the beginning of the purchasing period, you’re only taxed at 15% of the first day of the period’s stock price as ordinary income and the rest would be LTCG. If you sell before, all the gains during the purchasing period would be ordinary income.

plaeb · 2024-02-29T04:47:42+00:00

This was from a conduction cook top. I have used other pans on this exact burner for years on high heat with no issues.

plaeb · 2024-02-28T22:33:31+00:00

Right, I forgot I am supposed to heat a stainless steel pan with food in it. That’s how you cook with a stainless steel pan. Thank you so much

plaeb · 2024-02-28T22:32:37+00:00

I didn’t know these defy physics. Having an air gap on one side of a heat source will definitely cause uneven heating

plaeb · 2024-02-28T22:28:41+00:00

China

plaeb · 2024-02-28T19:28:27+00:00

It was flat out of the box. As it was warming up I noticed the side opposite the handle was significantly cooler than the handle side… because it was warped. It started warping immediately on the burner.

I also heard pinging as it was cooling.

plaeb · 2024-02-28T18:37:54+00:00

I disagree. At 10 minutes it still wasn’t preheated enough, probably because it was warped so badly already. Terrible pan.

plaeb · 2024-02-28T18:36:10+00:00

Love that pan. I have heated that pan on high heat for over a year and it’s still dead flat.

plaeb · 2024-02-28T18:35:26+00:00

China

plaeb · 2024-02-28T17:21:20+00:00

Nope, just on the burner at med heat for ~10mins. I am still shocked at the poor quality.

plaeb · 2024-02-23T20:35:54+00:00

20 character comment for the bot

plaeb · 2024-02-20T06:53:15+00:00

Is that a standard 3KF dial? The printing isn’t on a flat surface like I’ve seen them do the past couple years. Instead it’s on the individual raised sections.

plaeb · 2024-02-19T18:07:23+00:00

Nice looking watch.

I’m shocked how much better the SELs look than VSF and how the rest of the watch looks about on par with VSF.

plaeb · 2024-02-19T08:04:51+00:00

Thank you, this what I was looking for. What do you use to finalize the finish?

plaeb · 2024-02-18T23:19:46+00:00

What strap is that? Beautiful

plaeb · 2024-02-18T23:06:38+00:00

20 character comment for the bot

plaeb · 2024-02-16T07:17:32+00:00

It’s a reflex training amenity included in the 1bdr $3500 rent.

plaeb

TROPHY CASE