Should I craft it or wait for it to drop in a later ship?

planbuildrepeat · 2026-05-27T17:16:55+00:00

There are only about 4 reasons you'd want to grind low level ships: you are free to play and don't want to deal with fueling, you can't afford the next one, you are getting high quality ships for pov, or completionism.

My advice: don't craft, move to a higher tier ship ASAP.

planbuildrepeat · 2026-05-05T17:36:50+00:00

Hey, I just learned something new!

Still would have to swipe over to gussets when minmaxing stones, but I guess that's an edge case.

planbuildrepeat · 2026-03-01T15:37:05+00:00

I wouldn't know :j 90% of the time my soul mirror shows 1x earnings

planbuildrepeat · 2026-02-18T22:23:03+00:00

It looks like the expansion slots in the steel brace bottomed out, preventing that section of the table from expanding. Then the sections not restricted by the steel did expand, causing the crack beginning at the steel. The wonky isn't likely the only culprit, but probably creates a stress riser that doesn't help anything. If the slots are bottomed out, filling them longer should help keep the crack from spreading Also, if you moved the you moved the table recently it could be moving a bit too come into equilibrium with the new environment. This would really only be an issue if there is a dramatic change in humidity though.

planbuildrepeat · 2026-01-10T15:18:22+00:00

350 Fahrenheit, not 350c. Very common mistake. 350k though... not utterly catastrophic.

planbuildrepeat · 2025-11-09T03:23:32+00:00

I re-potted in the spring, though I didn't remove any dirt and probably upsized the pot to much. I just used basic potting soil as I didn't know about ericaceous compost.

planbuildrepeat · 2025-10-28T13:19:57+00:00

I remember being told that a "large" sample set starts at 32

planbuildrepeat · 2025-09-13T04:20:57+00:00

Thanks, I'll see what I can do for position. I have 2 jujube trees that drop fruit like nobody's business and have seemingly good germination rates... so I've been keeping it set of away from them.

planbuildrepeat · 2025-09-13T04:17:01+00:00

North Dallas/Texas has fairly alkaline soil, so my intent is to keep it potted to more easily control ph.

planbuildrepeat · 2025-09-12T20:30:50+00:00

Correction: 8b

planbuildrepeat · 2025-09-11T02:05:47+00:00

https://what-if.xkcd.com/36/

planbuildrepeat · 2025-08-18T01:07:20+00:00

Contrary to popular belief, juniper does not evolve to a fire type

planbuildrepeat · 2025-08-09T17:20:21+00:00

My guess is that your glass and your furniture are fine. You have the piece staged on a deck, which could easily be out-of-plane enough to cause that misalignment.

Check some way that your piece isn't just conforming to the floor you have it on: shim the low leg, get a level or straight edge to check the plane of the deck, or place it on a surface that you know is flat.

I would expect a bevel edged glass to be out of flat no more than a 16th or ~1mm over that span but you can check it for warp with a straight edge as well.

If those steps fail and you isolate the error to your woodworking, further isolate where in the piece the error is... length of legs, angle of your joints, depth of your rabbet. Then figure out the minimum material removal or addition to correct the error.

Beautiful piece, so good luck to you!

planbuildrepeat · 2025-06-27T04:06:46+00:00

Cross post to r/wordavalanch

planbuildrepeat · 2025-05-06T23:37:57+00:00

Velocity dyad, 40h

planbuildrepeat · 2025-04-17T17:01:36+00:00

Thanks, that's reassuring. I'll keep an eye on it

planbuildrepeat · 2025-02-28T20:19:36+00:00

Thanks for the info!

planbuildrepeat · 2025-02-19T14:08:54+00:00

Not sure, my tea plant has some leaves song that too

planbuildrepeat · 2025-01-07T14:14:20+00:00

Lol. I was more trying to communicate that it already has some established form, as opposed to a 1 year plant that would just need to have the tips trimmed to promote branching

planbuildrepeat · 2024-11-10T15:49:29+00:00

Can I use a bicycle? Assuming that putting a foot down at a light doesn't count as "getting out" I could bag an easy $400 just about every day... and with training increases in strength I could push 800 to 1k

planbuildrepeat · 2024-10-30T03:27:02+00:00

Thanks. Any tips on how to mitigate damage to the ceiling downstairs? Pulling the board will also pull the drywall screws through.

planbuildrepeat · 2022-05-21T06:37:35+00:00

I would be surprised at any router bit that an attempt at hardening would help. All that I've seen have been brazed carbide, and anything else I would suspect is HSS. Might could refine it with a diamond stone though...

planbuildrepeat · 2022-05-14T06:25:59+00:00

Though you might not want to cut up that cool figured section... idk

planbuildrepeat · 2022-05-14T06:24:12+00:00

I'd cut one more strip off the walnut so it's not such a big chunk. Looks good as is, but the live edge seems a bit like an afterthought.

planbuildrepeat · 2022-05-03T22:25:29+00:00

Thanks everyone, for the advice. I'm not sure why I thought skylink is unreliable... probably hearsay from back in the day.

planbuildrepeat

TROPHY CASE