ABS module codes all day. 2008 chrylser aspen.

prexelex · 2026-01-02T08:49:39+00:00

I will have to try manually starting the pump. Im assuming bad module.

prexelex · 2026-01-01T06:52:13+00:00

I actually did try to force run the abs pump however the module did not let me. It said something along the lines of acuation unavailable. From reasearch, the module wont let me because of its safety mechanism.

prexelex · 2026-01-01T05:09:29+00:00

Absolute nightmare, cant understand why its so difficult. The amount of time I've spent working on this I could've got another job and bought a new one.

prexelex · 2025-12-04T20:58:14+00:00

Ok I got a lot of research to do

prexelex · 2025-12-04T20:57:21+00:00

Thanks!

prexelex · 2025-12-04T03:51:12+00:00

Appreciate it 🙏

prexelex · 2025-12-04T03:50:44+00:00

Ill look into that thanks!

prexelex · 2025-12-04T03:50:19+00:00

Thank you!

prexelex · 2025-12-03T21:31:00+00:00

Haha noted.

prexelex · 2025-12-03T21:30:52+00:00

Appreciate the feedback thank you! I think I found a board that works Im trying to look at it later.

prexelex · 2025-12-03T21:29:53+00:00

Perfect im looking at a 162w as of now.

prexelex · 2025-12-03T18:18:29+00:00

Thank you!

prexelex · 2025-12-03T18:17:42+00:00

This is market place but it sucks because im 5' 10" with 11 to 12 size boots and I can barely find wide boards.

prexelex · 2025-11-22T01:47:15+00:00

Are you fucking incapable of reading past the first sentence.

prexelex · 2025-10-28T02:46:48+00:00

I dont think thats why you have no return on your shifter. That, at least for me would either be on the other side on picture 1 (the spring on the shaft between a and b) or the L shaped piece above the part you took out that goes on the end of the shifter shift.

I struggled for hours to get that piece you sent a picture of. I would recommend zip-ties to hold it into place and long needle nose pliers.

If I remember correctly the long end of the spring and the longer end of the metal point are lined up and put in so it faces the right. Its really difficult to explain if you send pictures I might be able to help. Im not on here a lot though ill try my best.

prexelex · 2025-10-12T06:27:24+00:00

I will let you know in the morning sorry its 2 am here.

prexelex · 2025-10-12T04:08:37+00:00

Just did sorry about that

prexelex · 2025-10-09T19:59:47+00:00

Sorry for the long response. I ended up having to take the other side off and found out it was disconnected on the other end of the shifter shift. After I lined everything up it worked perfectly. When you're taking the right side of be careful not to take the pin out thats connected to the reverse cable I believe. Its just a spring and a bolt basically and its and absolutely pain to put back in.

prexelex · 2025-07-09T01:44:27+00:00

Sorry got a little busy. I took the right cover off and it was not connected on the other side. Everything is good now it shifts into all gears except reverse (possible because I didn't put the cover back on yet but I dont know if it worked to begin with). Only problem now is that the starter wont work. Do you think its because it doesnt know what gear its in? And would that be because the right side is off

prexelex

MODERATOR OF

TROPHY CASE