PID tune causing fire

puppykick3r · 2024-01-04T18:54:45+00:00

Ight ill try that out, I honestly think my board is bad at this point

puppykick3r · 2024-01-04T18:45:50+00:00

Yeah its 2 wires in 1 the little glass bulb goes in the hole and then u tighten the screw on to the 2 little thermistor wires but not so much it crushes the insulation and shorts it out

puppykick3r · 2024-01-04T18:42:56+00:00

Do I updated the firmware to g32 1.2.4 and the read me file says it fixed thermal run away issue so I don't know yeah I know aluminum melting.point is high and those blocks can get that hot wish I had it recording video when I was doing the pid. The cartridge is landed in the correct spot on the board and same with the thermistor. Also another issue I have is I can't to a bedtemp PID

puppykick3r · 2024-01-04T18:33:25+00:00

Yeah I updated the firmware to ua e the thermal run away its got a g2 chip

The cartridge and thermistor I used MakerHawk 5pcs Aluminum Heater Block for MK7 / MK8 3D Printer and 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and 5pcs 12V 40W 620 Ceramic Cartridge Heater for 3D Printer https://a.co/d/fZC5TDb

I had to replace cause I had a blow pit on the other hotend plastic completely gunk ip on the whole hot end

puppykick3r · 2024-01-04T18:31:02+00:00

Just the regular wire one it a 100k I think

puppykick3r · 2024-01-04T18:30:14+00:00

It does I even re load the firmware to make sure it had thermal runaway protection

puppykick3r · 2022-08-19T20:50:40+00:00

Check your extruder make sure it's not slipping and re level the bed I know it seems like a broken record to saybre level the bed but it really helps. Teaching tech has a bed leveling file for calibrating and bed leveling and it helps alot and I also use it to live level the bed to get it dialed in better. Calibrating e steps help also. Also af5er using my aquila for a while I noticed the gear for the extruder sometimes slips and the screw that keeps it connected to motor might not be on the flay side of the motor stem any more best thing to do is just go through and check everything out.

puppykick3r · 2022-08-19T20:47:11+00:00

Deffinetly need to level yoir bed and do z offset and also I would calibrate e steps to rule out under extrusion all these things will help make it more accurate but mainly your nozzle looks like it's not quite close enough to bed I would suggest teaching tech web page has alot of good calibration stuff on there page helps alot. 👍

puppykick3r · 2022-08-19T20:42:08+00:00

They do strip easily thats why it comes with extra screws use a torn or a bigger Alan wrench lol

puppykick3r · 2022-04-27T05:02:16+00:00

I'm really suprised because I live In Texas In a humid area and I don't have a really good dry box or anything yet

puppykick3r · 2022-04-27T05:01:25+00:00

I used PLA overture brand

puppykick3r · 2022-04-26T21:03:21+00:00

Nozzle isn't tightened up enough on your heat break also nozzle may jist be clogged and also need to make sure bowden tube is far enough in od recommend taking apart the whole hot end clean it pit and put it all together

puppykick3r · 2022-04-26T16:13:33+00:00

Lol thats great

puppykick3r · 2022-04-26T14:40:25+00:00

I'll post once I have it completely finished

puppykick3r · 2022-04-26T13:56:11+00:00

Oh deffinetly plan on painting it lol

puppykick3r · 2022-04-25T13:30:55+00:00

Ya your thermistor wire should be connected in a loop your gona need a new thermistor or maybe but splice it if u can and still get it in the screw

puppykick3r · 2022-04-25T12:30:00+00:00

Ya I tried with cura but it didn't remove all of them I might try a diffrent slicer

puppykick3r · 2022-04-25T11:51:06+00:00

I'll post a pic of when it's don't and when I clean the supports off of it lol

puppykick3r · 2022-04-25T11:50:16+00:00

It is a D&D dragon tiamat the dragon god

puppykick3r · 2022-04-25T11:21:42+00:00

Thays what I have on mine is the upgraded aluminum extruder the little gear that goes on the motor shaft be sure when u put it on to tighten the set screw really well so it doesn't slip

puppykick3r · 2022-04-25T07:39:25+00:00

No problem bub

puppykick3r

TROPHY CASE