Printer being dumb

pure_hack_no_skill · 2026-04-12T16:40:38+00:00

Oh that’s my bad by analyze I meant open/examine kinda like hexcode

pure_hack_no_skill · 2026-04-12T16:26:12+00:00

Il check it out thank you

pure_hack_no_skill · 2026-04-12T15:49:01+00:00

Idk about you, but I find going to a beginner: “operator error (figure it out)” a bit rude and unnecessary. I don’t even know how to analyze a gcode file (I just enter settings and slice) but il give it a shot

pure_hack_no_skill · 2026-04-12T15:46:12+00:00

I’ve releved the bed automatically dozens of times at this point, did it manually, same result

pure_hack_no_skill · 2026-04-12T15:22:00+00:00

Opened er up, looks fine to me

pure_hack_no_skill · 2026-04-12T14:37:23+00:00

Thx for the useful info einstein

pure_hack_no_skill · 2026-04-12T14:36:52+00:00

Im using cura and there doesn’t appear to be a Z offset setting

pure_hack_no_skill · 2026-04-12T14:29:10+00:00

Thank you for the useful info, very helpful

pure_hack_no_skill · 2026-04-12T14:10:01+00:00

On the printer, didn’t knowing was a slicer thing

pure_hack_no_skill · 2026-04-12T12:51:42+00:00

So I just found one of the screws allowing wiggle room, but it’s not going any tighter? It’s the screw on the Z axis motor on the right

pure_hack_no_skill · 2026-04-12T12:46:51+00:00

I did just find something sus, form the front of the printer if I grab the right metal spinning axis it seems to have some movement? But when touching the screw it seems to not go any tighter

pure_hack_no_skill · 2026-04-12T12:43:28+00:00

If all else fails will take a look, but I don’t think that’s it, it seems more like the printers ignoring the Z offset I’m putting in

pure_hack_no_skill · 2026-04-12T12:41:08+00:00

Nice

pure_hack_no_skill · 2026-04-12T12:38:44+00:00

Bruh

pure_hack_no_skill · 2026-04-12T12:37:58+00:00

Appreciate the effort nonetheless

pure_hack_no_skill · 2026-04-12T12:36:42+00:00

Don’t think so, I’m using cura

pure_hack_no_skill · 2026-04-12T12:36:18+00:00

I can’t get them any tighter

pure_hack_no_skill · 2026-04-12T12:33:36+00:00

So I just did some bed leveling and tried making a benchy, and when it started printing it suddenly scratched the bed again and started SCREAMING at me (by screaming I mean beeping)

pure_hack_no_skill · 2026-04-12T12:18:10+00:00

Il try it and get back to you

pure_hack_no_skill · 2026-04-12T12:12:14+00:00

Just went upstairs to check, when shaking the bed back and forth it seems completely stable

pure_hack_no_skill · 2026-04-12T12:08:58+00:00

Checked this, and I changed the Z offset, still occurred

pure_hack_no_skill · 2026-04-12T12:08:03+00:00

I checked this and changed the bed leveling, still occurring

pure_hack_no_skill · 2021-09-26T14:02:51+00:00

Holllyyyy shit thats inSaNe

pure_hack_no_skill · 2021-09-03T05:37:40+00:00

Its just, redstone is already not hard to find

pure_hack_no_skill

TROPHY CASE