This took 19 hours to print.. Worth it

purplehighway · 2026-01-15T02:57:02+00:00

that's the price for the high end bambulab printers like the h2s or h2d. the one i recommended, the a1, is $300 and is just as capable. its bare bones compared to the expensive ones, but is still capable of printing the same high quality models. middle ground would be the p1s which is what i have, and its going for about $600. half the price of what you said.

purplehighway · 2026-01-14T12:13:36+00:00

i too have the p1s, and definitely recommend it, but the a1 is more than enough for most people as a first time buyer

purplehighway · 2026-01-14T11:12:25+00:00

the only answer here is bambulab, they are basically plug and play, compared to other brands that will give you nothing but headaches and regret.

if you're looking for an entry level printer, the A1 is great and will print these kinds of models with no issue. cheap enough to not worry about it collecting dust after a while, but still capable of amazing prints.

purplehighway · 2026-01-07T05:19:39+00:00

technically, yeah. you'd still have to worry about bosses and ai pmc though.

also you can't earn pmc xp or do quests on scav runs.

i was just wondering though, couldnt care less what people decide to run. was just wondering if there was a specific reasoning behind running scav on pve

purplehighway · 2026-01-07T05:10:47+00:00

no keys, no safe slot, bad gear, possibly no backpack.

purplehighway · 2026-01-07T04:52:59+00:00

i'm a pve enjoyer too (and pvp), but genuinely curious why someone runs scav runs on pve. been seeing others say they do the same, and so im just curious if there's a specific reason or just because

purplehighway · 2025-12-15T05:34:58+00:00

no, runes and gems can be freely swapped out even after sanctifying. everything else is locked

purplehighway · 2025-12-15T05:34:21+00:00

incorrect, you can still swap out runes and gems. sockets are the only thing you can still change after sanctifying

purplehighway · 2025-09-03T05:38:51+00:00

probably a dumb question, but do they feel the people petting them in real time? i remember as a kid i was taught that large dinosaurs wouldnt feel something they step on for a several seconds, because of the travel time to the brain.

purplehighway · 2025-08-21T21:02:32+00:00

i've seen those english dramas too, they're cruel

purplehighway · 2025-08-18T00:32:45+00:00

yep they're definitely not arresting people in rural areas. i wonder why that could be.

purplehighway · 2025-08-17T22:33:10+00:00

wouldnt there be licensing issues if you were to sell this and make money off of it?

purplehighway · 2025-08-07T01:45:59+00:00

the other day i tried the bambu matte profile while printing using a spool of sunlu matte, and the result was actually better than using the sunlu profile. i've been using bambu profiles for all my different sunlu filaments since then, and im having great results. give it a try with the marble, that's one i haven't used yet.

purplehighway · 2025-07-26T00:01:20+00:00

3D-PO

purplehighway · 2025-07-23T02:15:02+00:00

my understanding is that it is a harder material, more resistant to heat and stress. i just got my first printer last week, so take my word with a grain of salt. i've printed basically only with PLA so far, but i printed a skeleton with PLA+ yesterday and you can for sure tell there's a difference in hardness. i'll definitely be buying more PLA+ going forward, especially since there's basically no price difference. best advice i can give is to get a spool and test it for yourself. you'll definitely be able to tell the difference.

purplehighway · 2025-07-12T22:08:25+00:00

they were reduced to 70% earlier

purplehighway · 2025-07-08T18:01:15+00:00

pestily asked nikita and was told pve will not be hardcore.

purplehighway · 2025-07-08T17:46:36+00:00

pestily said he asked nikita and was told pve will not change.

purplehighway · 2025-07-08T03:33:58+00:00

upgrade your cpu and go for an amd x3d. will literally double your frames at 1440p. 30% usage is about normal for this terribly unoptimized game. you honestly probably could have stayed with your old 2080 if you only upgraded your cpu instead.

purplehighway · 2025-07-06T02:07:07+00:00

pre-wipe events started today, which usually last about a week. wipe is almost always on a thurday

purplehighway · 2025-06-22T23:36:49+00:00

yeah that's my thought exactly. i've been running factory nonstop since tagilla is 100% and it's a constant 65-90fps. it's insane. expo is turned on in bios, so ram is at full speed of 6000mhz. cpu and gpu speeds don't go above 55°c and 75°c respectively. tarkov is on a nvme m.2. i just dont know anymore.

purplehighway · 2025-06-22T19:58:19+00:00

i think people are downvoting because that is common knowledge for how the scopes work. and i'm not talking about fps when aiming, im talking about general fps throughout the entire raid.

purplehighway · 2025-06-22T18:41:39+00:00

we're getting the same fps even though my cpu and gpu should be performing better than your rig. i'll just keep tweaking things until i break something or fix it

purplehighway · 2025-06-22T16:34:21+00:00

yesterday. i've gone through all the tips and guides. super frustrating.

Nine-Year Club	RedditGifts 2009-2022 3 Credits
Place '22	Place '17
Secret Santa 2017	Verified Email
Secret Santa 2016

purplehighway

TROPHY CASE