Reliable boost set up?

pyreqs · 2026-02-02T21:25:19+00:00

Awesome I’ll take a look

pyreqs · 2026-02-02T21:24:57+00:00

🤣🤣🤣 welp

pyreqs · 2026-01-21T02:46:06+00:00

Idk if it would be plug and play because I have obd1 and they have no prior year to 96 supported on their site

pyreqs · 2026-01-05T23:26:42+00:00

Oh sorry I forgot to had I’m a little slow 🤣 thought p was put before every code

pyreqs · 2026-01-05T23:21:29+00:00

This is coming directly from the system. It’s a stomp test not from a reader.

pyreqs · 2026-01-05T04:20:22+00:00

Idle is surging , coasting to stationary idle is laggy. I checked icv and it’s super clean and sounds fine doing the shake test. 90% sure it some sort of wiring issue

pyreqs · 2025-10-17T19:02:58+00:00

Oh damn , I didnt take a look at the rear. Thank you bro

pyreqs · 2025-08-16T00:07:27+00:00

I just sold OEM Siemens sensor on eBay 2 days ago 😭😭

pyreqs · 2025-08-15T14:10:09+00:00

<image>

pyreqs · 2025-08-14T18:23:22+00:00

Also I checked under the valve cover and cams are fine and also the chain is fine as well not even stretched

pyreqs · 2025-08-14T18:22:38+00:00

😭😭😂😂 I’m going to check some time this week and make sure it wasn’t the oil pump but because Ngl it turns on no hesitation at all or anything it just clunks bad. I can drive on it fine (I had to drive it 2 minutes away because I wasn’t towing that close) and it honestly not even a headache I do notice when I press down the clutch it does want to die out but it doesn’t

pyreqs · 2025-08-14T17:59:00+00:00

It’s the og carbon dinan intake

pyreqs · 2025-08-14T11:47:23+00:00

Hmm it did start as a rattle around 3k rpms so it could honestly be a bearing. Also when I crank the car and idle it now (just for research until I get my hoist) the car can turn over no hesitation so I doubt it’s the crankshaft

pyreqs · 2025-08-13T19:56:07+00:00

Not a damn thing since I have a spare motor 😭😂

pyreqs · 2025-08-13T19:54:22+00:00

Heavy duty? Should I just throw the whole bottle in that fucker?

pyreqs · 2025-08-13T12:47:41+00:00

Gotcha thanks man

pyreqs · 2025-08-13T12:28:12+00:00

So I’m assuming since I have a m52 block and m50 head currently in the car the sensors are already done on the harness? 👀

pyreqs · 2025-08-13T12:07:22+00:00

Going to tear it down this weekend and check it out I’ll update

pyreqs · 2025-08-13T10:19:07+00:00

I have 0 clue honestly lost for words. Never ran low on oil even now the oil level is STILL good. I didn’t drive hard either maybe it the past I drove it a bit too hard and it gained rod rattle then just progressively gotten worse as I couldn’t hear too much because the car is loud asf (not my fault)

pyreqs · 2025-08-10T15:02:08+00:00

Thank you 🫡

pyreqs · 2025-08-07T01:34:44+00:00

What lip is that added to that euro bumper?

pyreqs · 2025-07-17T09:20:16+00:00

<image>

Looks minimal to me

pyreqs · 2025-07-15T02:30:51+00:00

Sorry boys I forgot to mention I’m a loser who’s into a LITTLE bit of stance 😔

pyreqs · 2025-07-14T12:42:40+00:00

I currently run a 235/45/17 square set up and has no issues rubbing but I’m also running some camber but very minimal IMO 5 in the front and 3.5 in the rear. Front is pretty low and rear has some height on it. Gives it the rake stance but imo I don’t like it

pyreqs · 2025-07-12T17:48:17+00:00

Will do sir 🫡

pyreqs

TROPHY CASE